Tubular transmission crossmember built using thick-wall 1.5" tubing & 3/16" steel.
Tubular transmission crossmember built using thick-wall 1.5" tubing & 3/16" steel.
Tubular transmission crossmember built using thick-wall 1.5" tubing & 3/16" steel.
Tubular transmission crossmember built using thick-wall 1.5" tubing & 3/16" steel.
Note: The tabs are loose and "unwelded".
The Porterbuilt cowl mounted hood hinges are the perfect solution to relocating the hood hinges once the factory inner fender wells have been removed. They are available for model years 1960-1972.
PRODUCTION TIME ON HOOD HINGES IS TYPICALLY 2-4 WEEKS Learn MoreThe Porterbuilt cowl mounted hood hinges are the perfect solution to relocating the hood hinges once the factory inner fender wells have been removed. They are available for model years 1960-1972 and start at $299 for the non-gas assist, or $399 with gas assist (this option is currently only available for the 67-72 trucks).
The non-gas assist version can later be upgraded to gas assist for $189.
PRODUCTION TIME ON HOOD HINGES IS TYPICALLY 2-4 WEEKS Learn MoreThe Porterbuilt cowl mounted hood hinges are the perfect solution to relocating the hood hinges once the factory inner fender wells have been removed. They are available for model years 1960-1972 and start at $299 for the non-gas assist, or $399 with gas assist (this option is currently only available for the 67-72 trucks).
The non-gas assist version can later be upgraded to gas assist for $189.
PRODUCTION TIME ON HOOD HINGES IS TYPICALLY 2-4 WEEKS Learn MoreThe Porterbuilt cowl mounted hood hinges are the perfect solution to relocating the hood hinges once the factory inner fender wells have been removed. They are available for model years 1960-1972.
PRODUCTION TIME ON HOOD HINGES IS TYPICALLY 2-4 WEEKS Learn MoreNew Inner Frame Stiffener for Level 2 & Level 3 Dropmember Equipped Trucks
New Boxed Inner Frame Stiffener for Level 2 & Level 3 Dropmember Equipped Trucks
New Boxed Inner Frame Stiffener for Level 2 & Level 3 Dropmember Equipped Trucks
New Boxed Inner Frame Stiffener for Level 1 Dropmember, Static & Stock Suspension Trucks
New Boxed Inner Frame Stiffener for Level 2 & Level 3 Dropmember Equipped Trucks
New Boxed Inner Frame Stiffener for Level 2 & Level 3 Dropmember Equipped Trucks
The 1947-54 Chevy Pickup Front Dropmember suspension system is a modular bolt-in sub-frame assembly engineered to incorporate Porterbuilt and C10 based suspension components.
When combined with a 2.5” drop spindle, 28” tall tire, and Porterbuilt Tubular Control Arms, the Level 2 Front will set the bottom of the cab approx. 5-6" inches off the ground at ride height.
The 1955-59 Chevy Pickup Front Dropmember suspension system is a modular bolt-in sub-frame assembly engineered to incorporate Porterbuilt and C10 based suspension components.
When combined with a 2.5” drop spindle, 28” tall tire, and Porterbuilt Tubular Control Arms, the Level 2 Front will set the bottom of the cab approx. 5-6" inches off the ground at ride height.
The 1963-72 Chevy Pickup Front Dropmember Coilover suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 2 Front will set the bottom of the cab approx. 4-6" inches off the ground at ride height.
The 1963-72 Chevy Pickup Front Dropmember Coilover suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 1 Front will set the bottom of the cab approx. 7-9" inches off the ground at ride height.
The 1973-87 Chevy Pickup Front Dropmember Coilover suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 1 Front will set the bottom of the cab approx. 7-9" inches off the ground at ride height.
The 1973-87 Chevy Pickup Front Dropmember Coilover suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 2 Front will set the bottom of the cab approx. 4-6" inches off the ground at ride height.
The 1955-59 Chevy Pickup Front Dropmember suspension system is a modular bolt-in sub-frame assembly engineered to incorporate Porterbuilt and C10 based suspension components.
When combined with a 2.5” drop spindle, 28” tall tire, and Porterbuilt Tubular Control Arms, the Level 3 Front will set the lowest point of the factory sheet metal on the ground when fully deflated.
The 1947-54 Chevy Pickup Front Dropmember suspension system is a modular bolt-in sub-frame assembly engineered to incorporate Porterbuilt and C10 based suspension components.
When combined with a 2.5” drop spindle, 28” tall tire, and Porterbuilt Tubular Control Arms, the Level 3 Front will set the lowest point of the factory sheet metal on the ground when fully deflated.
The 1960-62 Chevy Pickup Front Dropmember suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 3 Front will set the lowest point of the factory frame rails on the ground when fully deflated.
The 1963-72 Chevy Pickup Front Dropmember suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 3 Front will set the lowest point of the factory frame rails on the ground when fully deflated.
The 1963-72 Chevy Pickup Front Dropmember suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 1 Front will the lowest point of the factory frame rails approx. 3” off the ground when fully deflated.
The 1973-87 Chevy Pickup Front Dropmember suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 1 Front will the lowest point of the factory frame rails approx. 3” off the ground when fully deflated.
The 1973-87 Chevy Pickup Front Dropmember suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 3 Front will set the lowest point of the factory frame rails on the ground when fully deflated.
The 1960-62 Chevy Pickup Front Dropmember Coilover suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 2 Front Coilover system will set the lowest point of the factory frame rails approx. 5-6" inches off the ground at ride height.
These stainless steel headers are used with the Porterbuilt Level 3 Dropmember (Version 5, 6 & 7) when doing an LS swap.
Learn MoreThe Dropmember Rear Back Half suspension system is engineered fit 12-15" wide wheels.
Fits 1963-72 C10 Trucks
Level 2, Touring
Ride height measures approx. 5” when running a 30” tall tire.
The Dropmember Level 3 61-64 Ford F100 Front suspension system is a modular bolt-in sub-frame assembly engineered to incorporate Porterbuilt and C10 based suspension components.
When combined with a 2.5” drop spindle, 28” tall tire, and Porterbuilt Tubular Control Arms, the Level 3 Front will set the lowest point of the factory sheet metal on the ground when fully deflated.
The Dropmember Rear Back Half suspension system is engineered fit 12" wide wheels.
Fits 1960-62 C10 Trucks
Level 2, Touring
Ride height measures approx. 5” when running a 30” tall tire.
The Dropmember Rear Back Half suspension system is engineered to lay frame with 12" wide wheels.
Fits 1960-62 C10 Trucks
Level 3, Extreme
Ride height measures approx. 5” when running a 30” tall tire, and the frame will rest on the ground when deflated.
The Dropmember Rear Back Half suspension system is engineered to lay frame with 12-15" wide wheels.
Fits 1963-72 C10 Trucks
Level 3, Extreme
Ride height measures approx. 5” and the frame will rest on the ground when deflated.
If you are thinking about lowering your C10 truck more than four inches in the rear, a longer trac-bar will be a necessity! The Porterbuilt Fully Adjustable Trac-bar has an overall length of just over 34 inches. The longer the bar, the less side to side shift the differential will experience through suspension travel. The new mounting brackets also relocate the bar lowering the rear roll-center, and the bar length can be tuned while still mounted on the truck!
Learn MoreThe new Porterbuilt sway bar is manufactured in-house and is available for Version 7 Dropmember equipped trucks. It comes raw and includes all mounting hardware.
Learn MoreThe new Porterbuilt sway bar is manufactured in-house and is available for early Dropmember equipped trucks. It comes raw and includes all mounting hardware.
Learn MoreThe new Porterbuilt sway bar is manufactured in-house and is available for trucks equipped with PB Fab control arms and the factory crossmember. It comes raw and includes all mounting hardware.
Learn MoreThe stage 1 rear kit is both an economical and easy way to lower the rear of your 63-72 C10′s trailing arm suspension. The air spring and mounting plates replace the factory steel coil spring, allowing a better ride quality and adjustability! Our Stage 1 shock relocator brackets improve shock function by decreasing the shock angle!
Learn MoreThe Porterbuilt Bolt-on Body Drop for the 1967-1972 C10 is for those guys who just can’t be low enough! It is designed to make it easier to set the pinch weld level to the bottom of the frame.
Learn MoreTubular trailing arm crossmember built using thick-wall 1.5" tubing & 3/16" steel.
Tubular core support crossmember built using thick-wall 1.5" tubing & 3/16" steel.
Tubular core support crossmember built using thick-wall 1.5" tubing & 3/16" steel.
Tubular core support crossmember built using thick-wall 1.5" tubing & 3/16" steel.
Tubular core support crossmember built using thick-wall 1.5" tubing & 3/16" steel.
Tubular core support crossmember built using thick-wall 1.5" tubing & 3/16" steel.
Tubular trailing arm crossmember built using thick-wall 1.5" tubing & 3/16" steel.
Tubular trailing arm crossmember built using thick-wall 1.5" tubing & 3/16" steel.
Tubular core support crossmember built using thick-wall 1.5" tubing & 3/16" steel.
The Porterbuilt Stage 2 Basic Front Kit for '63-'87 Chevy Trucks improves ride quality and overall driveability by replacing the factory lower control arms and and factory coil spring with an air spring.
Learn MoreLooking for an easy way to switch over to air suspension without breaking the bank? The Stage 1 front kit is an inexpensive and simple way to do just that! The Stage 1 front kit is designed to replace the factory steel coil spring with an air spring while maintaining the factory control arms.
NOTE: ALL CONTROL ARMS ARE DESIGNED TO USE PROFORGED BALL JOINTS. .
Learn MoreAll Viair 444C compressors feature a head assembly that includes a newly-developed, patents pending intercooler head. Additionally, they are equipped with a stainless steel braided leader hose with inline check valve assembly that serves to protect the compressor by eliminating the possibility of high amperage restarts.
Learn MoreTubular carrier bearing crossmember built using thick-wall 1.5" tubing & 3/16" steel.
Boxed Trailing Arm Crossmember built using 3/16" steel for a 2-piece driveshaft configuration.
Tubular rear frame crossmember built using thick-wall 1.5" tubing & 3/16" steel.
Tubular rear frame crossmember built using thick-wall 1.5" tubing & 3/16" steel.
Tubular rear frame crossmember built using thick-wall 1.5" tubing & 3/16" steel.
Tubular rear frame crossmember built using thick-wall 1.5" tubing & 3/16" steel.
1967-72 Longbed to Shortbed Conversion Kit
Includes templates and c-channel supports
Available for C10 and C20 trucks
Welding is required Learn More
If you are looking for the best possible kit to convert your truck to air suspension but maintain your factory front crossmember, this is the kit for you. The Porterbuilt Stage 2 Deluxe Front Kit for '63-'87 Chevy Trucks replaces your factory control arms and coil springs, lowering your truck and improving handling, without replacing the factory front crossmember.
Learn MoreProduct Number: 14040
Approx 19 Gallons
1973-87 Chevy C10
Side Fill
Aeromotive In-Tank Pump