The Porterbuilt Stage 2 Rear “Deluxe” Kit for 63-72 C10 is an engineered bolt-in suspension system designed to lower your truck as low as possible while maintaining the factory bed floor. The Stage 2 “Deluxe” is just that, it replaces all the factory crossmembers (from the trailing arm cross-member back) with tubular versions that are designed to bolt right in! It also includes our fully adjustable trac bar for improved handling and performance. If you are looking for the best possible kit to lower your C10 and keep the bed-floor in tact… this is the one!
Learn MoreIf you are looking for the best possible kit to convert your truck to air suspension but maintain your factory front crossmember, this is the kit for you. The Porterbuilt Stage 2 Deluxe Front Kit for '63-'87 Chevy Trucks replaces your factory control arms and coil springs, lowering your truck and improving handling, without replacing the factory front crossmember.
Learn MoreReplacement Shock Kit
Applications:
Dropmember Level 1, Dropmember Level 2, Dropmember Level 3
Stage 1 Front, Stage 2 Front
Stage 1 Rear, Stage 2 Rear Basic, Stage 2 Rear Deluxe
The Porterbuilt Stage 2 Basic Front Kit for '63-'87 Chevy Trucks improves ride quality and overall driveability by replacing the factory lower control arms and and factory coil spring with an air spring.
Learn MoreThe stage 1 rear kit is both an economical and easy way to lower the rear of your 63-72 C10′s trailing arm suspension. The air spring and mounting plates replace the factory steel coil spring, allowing a better ride quality and adjustability! Our Stage 1 shock relocator brackets improve shock function by decreasing the shock angle!
Learn MoreLooking for an easy way to switch over to air suspension without breaking the bank? The Stage 1 front kit is an inexpensive and simple way to do just that! The Stage 1 front kit is designed to replace the factory steel coil spring with an air spring while maintaining the factory control arms.
NOTE: ALL CONTROL ARMS ARE DESIGNED TO USE PROFORGED BALL JOINTS. .
Learn MoreThe 1973-87 Chevy Pickup Rear Level 2 Coilover Dropmember suspension system is engineered to improve ride quality, performance, aesthetics, and strength.
The 1963-72 Chevy Pickup Rear Level 2 Coilover Dropmember suspension system is engineered to improve ride quality, performance, aesthetics, and strength.
The Dropmember Rear Back Half suspension system is engineered fit 12" wide wheels.
Fits 1960-62 C10 Trucks
Level 2, Touring
Ride height measures approx. 5” when running a 30” tall tire.
The Dropmember Rear Back Half suspension system is engineered fit 12-15" wide wheels.
Fits 1963-72 C10 Trucks
Level 2, Touring
Ride height measures approx. 5” when running a 30” tall tire.
The 1955-59 Chevy Pickup Rear Coilover Dropmember suspension system is engineered to improve ride quality, performance, aesthetics, and strength.
The 1947-54 Chevy Pickup Rear Coilover Dropmember suspension system is engineered to improve ride quality, performance, aesthetics, and strength.
The Porterbuilt 1960-62 Rear coilover suspension system is a modular suspension system designed to replace the factory components and improve ride quality, performance, aesthetics, and strength.
Ride height measures approx. 6” when running a 30” tall tire (measurements are taken from bottom of the cab to the ground).The 1973-87 Chevy Pickup Rear Level 2 Coilover Dropmember suspension system is engineered to improve ride quality, performance, aesthetics, and strength.
The 1963-72 Chevy Pickup Rear Level 2 Coilover Dropmember suspension system is engineered to improve ride quality, performance, aesthetics, and strength.
The 1963-72 Chevy Pickup Front Dropmember Coilover suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 2 Front will set the bottom of the cab approx. 4-6" inches off the ground at ride height.
The 1973-87 Chevy Pickup Front Dropmember Coilover suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 2 Front will set the bottom of the cab approx. 4-6" inches off the ground at ride height.
16" Rear Big Brake Kit From Little Shop Manufacturing
Available with Wilwood 6 Piston Calipers or MFG 6 Piston Calipers
Comes with Drilled & Slotted Rotors
FITS BIG FORD NEW STYLE REAREND FLANGE ONLY!
Learn MoreThis standard Firestone air spring offers maximum load support and operates at up to 100 psi. The spring has a 1/4" inflation port, a ride height of 8.25" and a maximum diameter of 5.70".
* Includes 2 air springs
Learn MoreAir Lift Performance is proud to announce the second model from the brand new Dominator series line of air springs: the Dominator D2600!
*Includes 2 air bags
Learn MoreThe Dropmember Rear Back Half suspension system is engineered to lay frame with 12-15" wide wheels.
Fits 1963-72 C10 Trucks
Level 3, Extreme
Ride height measures approx. 5” and the frame will rest on the ground when deflated.
The Dropmember Rear Back Half suspension system is engineered to lay frame with 12" wide wheels.
Fits 1960-62 C10 Trucks
Level 3, Extreme
Ride height measures approx. 5” when running a 30” tall tire, and the frame will rest on the ground when deflated.
The 1963-72 Chevy Pickup Rear Level 1 Airbag Dropmember suspension system is designed to replace the factory components and improve ride quality, performance, aesthetics, and strength.
The 1973-87 Chevy Pickup Rear Level 1 Airbag Dropmember suspension system is designed to replace the factory components and improve ride quality, performance, aesthetics, and strength.
The 1947-54 Chevy Pickup Rear Dropmember suspension system is engineered to lay body with large diameter wheel/tire combinations. (Recommended to run no wider than a 10” wheel)
The 1960-62 Chevy Pickup Rear Dropmember suspension system is engineered to lay body with large diameter wheel/tire combinations. (Recommended to run no wider than a 10” wheel)
The 1955-59 Chevy Pickup Rear Airbag Dropmember suspension system is engineered to lay body with large diameter wheel/tire combinations. (Recommended to run no wider than a 10” wheel)
The 1973-87 Chevy Pickup Rear Level 3 Airbag Dropmember suspension system is engineered to lay frame with large diameter wheel/tire combinations.
The 1963-72 Chevy Pickup Rear Level 3 Airbag Dropmember suspension system is engineered to lay frame with large diameter wheel/tire combinations.
The 1963-72 Chevy Blazer 4WD Rear Level 3 Airbag Dropmember suspension system is engineered to lay frame with large diameter wheel/tire combinations.
The 1963-72 Chevy Blazer 2WD Rear Level 3 Airbag Dropmember suspension system is engineered to lay frame with large diameter wheel/tire combinations.
If you are thinking about lowering your C10 truck more than four inches in the rear, a longer trac-bar will be a necessity! The Porterbuilt Fully Adjustable Trac-bar has an overall length of just over 34 inches. The longer the bar, the less side to side shift the differential will experience through suspension travel. The new mounting brackets also relocate the bar lowering the rear roll-center, and the bar length can be tuned while still mounted on the truck!
Learn MoreTubular rear frame crossmember built using thick-wall 1.5" tubing & 3/16" steel.
Tubular rear frame crossmember built using thick-wall 1.5" tubing & 3/16" steel.
Tubular rear frame crossmember built using thick-wall 1.5" tubing & 3/16" steel.
Tubular rear frame crossmember built using thick-wall 1.5" tubing & 3/16" steel.
Tubular trailing arm crossmember built using thick-wall 1.5" tubing & 3/16" steel.
New Inner Frame Stiffener for Level 2 & Level 3 Dropmember Equipped Trucks
The 1947-54 Chevy Pickup Front Dropmember suspension system is a modular bolt-in sub-frame assembly engineered to incorporate Porterbuilt and C10 based suspension components.
When combined with a 2.5” drop spindle, 28” tall tire, and Porterbuilt Tubular Control Arms, the Level 2 Front will set the bottom of the cab approx. 5-6" inches off the ground at ride height.
The 1955-59 Chevy Pickup Front Dropmember suspension system is a modular bolt-in sub-frame assembly engineered to incorporate Porterbuilt and C10 based suspension components.
When combined with a 2.5” drop spindle, 28” tall tire, and Porterbuilt Tubular Control Arms, the Level 2 Front will set the bottom of the cab approx. 5-6" inches off the ground at ride height.
The 1960-62 Chevy Pickup Front Dropmember Coilover suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 2 Front Coilover system will set the lowest point of the factory frame rails approx. 5-6" inches off the ground at ride height.
New Boxed Inner Frame Stiffener for Level 2 & Level 3 Dropmember Equipped Trucks
New Boxed Inner Frame Stiffener for Level 2 & Level 3 Dropmember Equipped Trucks
New Boxed Inner Frame Stiffener for Level 2 & Level 3 Dropmember Equipped Trucks
New Boxed Inner Frame Stiffener for Level 2 & Level 3 Dropmember Equipped Trucks
Boxed Trailing Arm Crossmember built using 3/16" steel for a 2-piece driveshaft configuration.
The 1963-72 Chevy Pickup Front Dropmember Coilover suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 1 Front will set the bottom of the cab approx. 7-9" inches off the ground at ride height.
The 1973-87 Chevy Pickup Front Dropmember Coilover suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 1 Front will set the bottom of the cab approx. 7-9" inches off the ground at ride height.
Wilwood Forged Narrow Superlite 6R Front Brake Kit
14" Rotors, SRP Drilled & Slotted Available
6 Piston Calipers, Red or Black Available
18" Minimum Wheel Diameter
* FOR USE WITH WILWOOD C10 STEEL SPINDLES
Learn MoreWilwood Forged Narrow Superlite 6R Front Brake Kit
13" Rotors, SRP Drilled & Slotted Available
6 Piston Calipers, Red or Black Available
17" Minimum Wheel Diameter
* FOR USE WITH WILWOOD C10 STEEL SPINDLES
Learn MoreWilwood Forged Narrow Superlite 6R Front Brake Kit
14" Rotors, SRP Drilled & Slotted Available
6 Piston Calipers, Red or Black Available
18" Minimum Wheel Diameter
* FOR USE WITH WILWOOD C10 PRO SPINDLES
Learn MoreWilwood Forged Narrow Superlite 6R Front Brake Kit
13.06" Rotors, SRP Drilled & Slotted Available
6 Piston Calipers, Red or Black Available
17" Minimum Wheel Diameter
* FOR USE WITH WILWOOD C10 PRO SPINDLES
Learn MoreWilwood Forged Narrow Superlite 6R Front Brake Kit
12.19" Rotors, SRP Drilled & Slotted Available
6 Piston Calipers, Red or Black Available
15" Minimum Wheel Diameter
* FOR USE WITH WILWOOD C10 PRO SPINDLES
Learn MoreWilwood Forged Narrow Superlite 6R Front Brake Kit
13.06" Rotors, Drilled & Slotted Available
6 Piston Calipers, Red or Black Available
17" Minimum Wheel Diameter
* FOR USE WITH CPP MODULAR SPINDLES
Learn MoreWilwood Forged Narrow Superlite 6R Front Brake Kit
12" 1 Piece Rotor and Hats, SRP Drilled & Slotted Available
6 Piston Calipers, Red or Black Available
15" Minimum Wheel Diameter
* FOR USE WITH WILWOOD C10 STEEL SPINDLES
Learn MoreWilwood Forged Narrow Superlite 6R Front Brake Kit
6 Lug
14" Rotors, SRP Drilled & Slotted Available
6 Piston Calipers, Red or Black Available
18" Minimum Wheel Diameter
* FOR USE WITH WILWOOD C10 STEEL SPINDLES
Learn MoreWilwood Forged Narrow Superlite 6R Front Brake Kit
6 Lug
13" Rotors, SRP Drilled & Slotted Available
6 Piston Calipers, Red or Black Available
17" Minimum Wheel Diameter
* FOR USE WITH WILWOOD C10 STEEL SPINDLES
Learn MoreWilwood Forged Narrow Superlite 6R Front Brake Kit
6 Lug
14" Rotors, Drilled & Slotted Available
6 Piston Calipers, Red or Black Available
18" Minimum Wheel Diameter
* FOR USE WITH CPP MODULAR SPINDLES
Learn MoreWilwood Forged Narrow Superlite 6R Front Brake Kit
6 Lug
13.06" Rotors, Drilled & Slotted Available
6 Piston Calipers, Red or Black Available
17" Minimum Wheel Diameter
* FOR USE WITH CPP MODULAR SPINDLES
Learn MoreWilwood Forged Narrow Superlite 6R Front Brake Kit
6 Lug
12" 1 Piece Rotor and Hats, SRP Drilled & Slotted Available
6 Piston Calipers, Red or Black Available
15" Minimum Wheel Diameter
* FOR USE WITH WILWOOD C10 STEEL SPINDLES
Learn More16" Big Brake Kit From Little Shop Manufacturing
Available with Wilwood 6 Piston Calipers or MFG 6 Piston Calipers
Comes with Drilled & Slotted Rotors
FITS WILWOOD ALUMINUM PROSPINDLE ONLY (NOT INCLUDED)
Learn MoreWilwood Forged Narrow Superlite 6R Front Brake Kit
14" Rotors, Drilled & Slotted Available
6 Piston Calipers, Red or Black Available
18" Minimum Wheel Diameter
* FOR USE WITH CPP MODULAR SPINDLES
Learn More1967-72 Longbed to Shortbed Conversion Kit
Includes templates and c-channel supports
Available for C10 and C20 trucks
Welding is required Learn More
The 1955-59 Chevy Pickup Front Dropmember suspension system is a modular bolt-in sub-frame assembly engineered to incorporate Porterbuilt and C10 based suspension components.
When combined with a 2.5” drop spindle, 28” tall tire, and Porterbuilt Tubular Control Arms, the Level 3 Front will set the lowest point of the factory sheet metal on the ground when fully deflated.