The Porterbuilt 1960-62 Rear coilover suspension system is a modular suspension system designed to replace the factory components and improve ride quality, performance, aesthetics, and strength.
Ride height measures approx. 6” when running a 30” tall tire (measurements are taken from bottom of the cab to the ground).If you are thinking about lowering your C10 truck more than four inches in the rear, a longer trac-bar will be a necessity! The Porterbuilt Fully Adjustable Trac-bar has an overall length of just over 34 inches. The longer the bar, the less side to side shift the differential will experience through suspension travel. The new mounting brackets also relocate the bar lowering the rear roll-center, and the bar length can be tuned while still mounted on the truck!
Learn MoreTubular transmission crossmember built using thick-wall 1.5" tubing & 3/16" steel.
Note: The tabs are loose and "unwelded".
Tubular rear frame crossmember built using thick-wall 1.5" tubing & 3/16" steel.
Looking for an easy way to switch over to air suspension without breaking the bank? The Stage 1 front kit is an inexpensive and simple way to do just that! The Stage 1 front kit is designed to replace the factory steel coil spring with an air spring while maintaining the factory control arms.
NOTE: ALL CONTROL ARMS ARE DESIGNED TO USE PROFORGED BALL JOINTS. .
Learn MoreThis power rack and pinion from CPP is new, not a rebuilt or remanufactured rack.
Learn MoreAir Lift Performance 3H combines pressure-based control with ride-height sensing technology. While both types of air management have been utilized before, this is the first product to harness the benefits of both sytems – instantly improving suspension control, performance, and vehicle ride flexibility.
Learn MoreThe 1947-54 Chevy Pickup Rear Dropmember suspension system is engineered to lay body with large diameter wheel/tire combinations. (Recommended to run no wider than a 10” wheel)
New Boxed Inner Frame Stiffener for Level 2 & Level 3 Dropmember Equipped Trucks
THESE CONTROL ARMS ARE FOR VERSION 7, COILOVER DROPMEMBER APPLICATIONS ONLY.
Porterbuilt tubular control arms are built using thick-wall DOM tubing and CNC cut 3/16" pickeled plate steel. All bushing pivot tubes and ball joint cups are TIG welded.
Includes shafts, bushings, and Grade 8 hardware for installation.
NOTE: ALL CONTROL ARMS ARE DESIGNED TO USE PROFORGED BALL JOINTS. .
Learn MoreProduct Number: 14001
Approx 19 Gallons
1963-72 Chevy C10
Standard
Bed Fill
Non-EFI
* Shown With Optional Rollover Vent and Sending Unit Installed.
Learn MoreThe 1947-54 Chevy Pickup Front Dropmember suspension system is a modular bolt-in sub-frame assembly engineered to incorporate Porterbuilt and C10 based suspension components.
When combined with a 2.5” drop spindle, 28” tall tire, and Porterbuilt Tubular Control Arms, the Level 3 Front will set the lowest point of the factory sheet metal on the ground when fully deflated.
The Porterbuilt cowl mounted hood hinges are the perfect solution to relocating the hood hinges once the factory inner fender wells have been removed. They are available for model years 1960-1972.
PRODUCTION TIME ON HOOD HINGES IS TYPICALLY 2-4 WEEKS Learn MoreReplacement Shock Kit
Applications:
Dropmember Level 1, Dropmember Level 2, Dropmember Level 3
Stage 1 Front, Stage 2 Front
Stage 1 Rear, Stage 2 Rear Basic, Stage 2 Rear Deluxe
The stage 1 rear kit is both an economical and easy way to lower the rear of your 63-72 C10′s trailing arm suspension. The air spring and mounting plates replace the factory steel coil spring, allowing a better ride quality and adjustability! Our Stage 1 shock relocator brackets improve shock function by decreasing the shock angle!
Learn MoreThe 1947-54 Chevy Pickup Rear Coilover Dropmember suspension system is engineered to improve ride quality, performance, aesthetics, and strength.
New Boxed Inner Frame Stiffener for Level 2 & Level 3 Dropmember Equipped Trucks
Product Number: 14002
Approx 19 Gallons
1963-72 Chevy C10
Standard
Side Fill
Non-EFI
* Shown With Optional Rollover Vent and Sending Unit Installed.
Learn MoreThe Porterbuilt cowl mounted hood hinges are the perfect solution to relocating the hood hinges once the factory inner fender wells have been removed. They are available for model years 1960-1972.
PRODUCTION TIME ON HOOD HINGES IS TYPICALLY 2-4 WEEKS Learn MoreThe 1947-54 Chevy Pickup Front Dropmember suspension system is a modular bolt-in sub-frame assembly engineered to incorporate Porterbuilt and C10 based suspension components.
When combined with a 2.5” drop spindle, 28” tall tire, and Porterbuilt Tubular Control Arms, the Level 2 Front will set the bottom of the cab approx. 5-6" inches off the ground at ride height.
Porterbuilt tubular control arms are built using thick-wall DOM tubing and CNC cut 3/16" pickeled plate steel. All bushing pivot tubes and ball joint cups are TIG welded.
Available in the following configurations:
1" Forward
1" Narrowed
1" Forward & 1" Narrowed
Standard Length
Includes upper and lower shafts, bushings, and Grade 8 hardware for installation.
NOTE: ALL CONTROL ARMS ARE DESIGNED TO USE PROFORGED BALL JOINTS. .
Learn MoreThe Porterbuilt Stage 2 Basic Front Kit for '63-'87 Chevy Trucks improves ride quality and overall driveability by replacing the factory lower control arms and and factory coil spring with an air spring.
Learn MoreProduct Number: 14003
Approx 19 Gallons
1963-72 Chevy C10
Side Fill
Aeromotive In-Tank Pump
Air Lift Performance 3P combines pressure-based control with the ability to add ride-height sensing technology with the upgrade to height sensors. While both types of air management have been utilized before, this is the first product to harness the benefits of both sytems – instantly improving suspension control, performance, and vehicle ride flexibility.
Learn MoreNew Boxed Inner Frame Stiffener for Level 1 Dropmember, Static & Stock Suspension Trucks
The 1955-59 Chevy Pickup Rear Airbag Dropmember suspension system is engineered to lay body with large diameter wheel/tire combinations. (Recommended to run no wider than a 10” wheel)
The 1955-59 Chevy Pickup Front Dropmember suspension system is a modular bolt-in sub-frame assembly engineered to incorporate Porterbuilt and C10 based suspension components.
When combined with a 2.5” drop spindle, 28” tall tire, and Porterbuilt Tubular Control Arms, the Level 3 Front will set the lowest point of the factory sheet metal on the ground when fully deflated.
The 1955-59 Chevy Pickup Rear Coilover Dropmember suspension system is engineered to improve ride quality, performance, aesthetics, and strength.
New Inner Frame Stiffener for Level 2 & Level 3 Dropmember Equipped Trucks
New Boxed Inner Frame Stiffener for Level 2 & Level 3 Dropmember Equipped Trucks
THESE CONTROL ARMS ARE FOR EARLY (PRE VERSION 7) DROPMEMBER APPLICATIONS ONLY.
Porterbuilt tubular control arms are built using thick-wall DOM tubing and CNC cut 3/16" pickeled plate steel. All bushing pivot tubes and ball joint cups are TIG welded.
Includes shafts, bushings, and Grade 8 hardware for installation.
NOTE: ALL CONTROL ARMS ARE DESIGNED TO USE PROFORGED BALL JOINTS. .
Learn MoreThe 1955-59 Chevy Pickup Front Dropmember suspension system is a modular bolt-in sub-frame assembly engineered to incorporate Porterbuilt and C10 based suspension components.
When combined with a 2.5” drop spindle, 28” tall tire, and Porterbuilt Tubular Control Arms, the Level 2 Front will set the bottom of the cab approx. 5-6" inches off the ground at ride height.
If you are looking for the best possible kit to convert your truck to air suspension but maintain your factory front crossmember, this is the kit for you. The Porterbuilt Stage 2 Deluxe Front Kit for '63-'87 Chevy Trucks replaces your factory control arms and coil springs, lowering your truck and improving handling, without replacing the factory front crossmember.
Learn MoreThe 1960-62 Chevy Pickup Rear Dropmember suspension system is engineered to lay body with large diameter wheel/tire combinations. (Recommended to run no wider than a 10” wheel)
The Porterbuilt cowl mounted hood hinges are the perfect solution to relocating the hood hinges once the factory inner fender wells have been removed. They are available for model years 1960-1972 and start at $299 for the non-gas assist, or $399 with gas assist (this option is currently only available for the 67-72 trucks).
The non-gas assist version can later be upgraded to gas assist for $189.
PRODUCTION TIME ON HOOD HINGES IS TYPICALLY 2-4 WEEKS Learn MoreThe 1960-62 Chevy Pickup Front Dropmember suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 3 Front will set the lowest point of the factory frame rails on the ground when fully deflated.
New Boxed Inner Frame Stiffener for Level 2 & Level 3 Dropmember Equipped Trucks
The Porterbuilt cowl mounted hood hinges are the perfect solution to relocating the hood hinges once the factory inner fender wells have been removed. They are available for model years 1960-1972 and start at $299 for the non-gas assist, or $399 with gas assist (this option is currently only available for the 67-72 trucks).
The non-gas assist version can later be upgraded to gas assist for $189.
PRODUCTION TIME ON HOOD HINGES IS TYPICALLY 2-4 WEEKS Learn MoreThe Porterbuilt Stage 2 Rear “Deluxe” Kit for 63-72 C10 is an engineered bolt-in suspension system designed to lower your truck as low as possible while maintaining the factory bed floor. The Stage 2 “Deluxe” is just that, it replaces all the factory crossmembers (from the trailing arm cross-member back) with tubular versions that are designed to bolt right in! It also includes our fully adjustable trac bar for improved handling and performance. If you are looking for the best possible kit to lower your C10 and keep the bed-floor in tact… this is the one!
Learn MoreProduct Number: 14038
Approx 19 Gallons
1973-87 Chevy C10
Standard
Bed Fill
Non-EFI
* Pictures may show optional accessories installed. Depending upon the options you choose your tank may vary slightly from shown.
Learn MoreThe 1960-62 Chevy Pickup Front Dropmember Coilover suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 2 Front Coilover system will set the lowest point of the factory frame rails approx. 5-6" inches off the ground at ride height.
Product Number: 14039
Approx 19 Gallons
1973-87 Chevy C10
Standard
Side Fill
Non-EFI
* Pictures may show optional accessories installed. Depending upon the options you choose your tank may vary slightly from shown.
Learn MoreThe 1963-72 Chevy Pickup Rear Level 1 Airbag Dropmember suspension system is designed to replace the factory components and improve ride quality, performance, aesthetics, and strength.
The 1963-72 Chevy Pickup Front Dropmember suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 1 Front will the lowest point of the factory frame rails approx. 3” off the ground when fully deflated.
Replacement hood hinge strut for older style Gas Assist Hood Hinge kits.
The 1963-72 Chevy Blazer 2WD Rear Level 3 Airbag Dropmember suspension system is engineered to lay frame with large diameter wheel/tire combinations.
The 1963-72 Chevy Blazer 4WD Rear Level 3 Airbag Dropmember suspension system is engineered to lay frame with large diameter wheel/tire combinations.
The 1963-72 Chevy Pickup Front Dropmember suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 3 Front will set the lowest point of the factory frame rails on the ground when fully deflated.
The 1963-72 Chevy Pickup Rear Level 3 Airbag Dropmember suspension system is engineered to lay frame with large diameter wheel/tire combinations.
The Dropmember Rear Back Half suspension system is engineered to lay frame with 12-15" wide wheels.
Fits 1963-72 C10 Trucks
Level 3, Extreme
Ride height measures approx. 5” and the frame will rest on the ground when deflated.
The Dropmember Rear Back Half suspension system is engineered fit 12-15" wide wheels.
Fits 1963-72 C10 Trucks
Level 2, Touring
Ride height measures approx. 5” when running a 30” tall tire.
The Dropmember Rear Back Half suspension system is engineered to lay frame with 12" wide wheels.
Fits 1960-62 C10 Trucks
Level 3, Extreme
Ride height measures approx. 5” when running a 30” tall tire, and the frame will rest on the ground when deflated.
The Dropmember Rear Back Half suspension system is engineered fit 12" wide wheels.
Fits 1960-62 C10 Trucks
Level 2, Touring
Ride height measures approx. 5” when running a 30” tall tire.
The 1963-72 Chevy Pickup Front Dropmember Coilover suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 1 Front will set the bottom of the cab approx. 7-9" inches off the ground at ride height.
Product Number: 14040
Approx 19 Gallons
1973-87 Chevy C10
Side Fill
Aeromotive In-Tank Pump
The 1963-72 Chevy Pickup Rear Level 2 Coilover Dropmember suspension system is engineered to improve ride quality, performance, aesthetics, and strength.
The 1963-72 Chevy Pickup Front Dropmember Coilover suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 2 Front will set the bottom of the cab approx. 4-6" inches off the ground at ride height.
The 1963-72 Chevy Pickup Rear Level 2 Coilover Dropmember suspension system is engineered to improve ride quality, performance, aesthetics, and strength.
The 1973-87 Chevy Pickup Front Dropmember suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 1 Front will the lowest point of the factory frame rails approx. 3” off the ground when fully deflated.
The 1973-87 Chevy Pickup Front Dropmember suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 3 Front will set the lowest point of the factory frame rails on the ground when fully deflated.
The 1973-87 Chevy Pickup Rear Level 1 Airbag Dropmember suspension system is designed to replace the factory components and improve ride quality, performance, aesthetics, and strength.
The 1973-87 Chevy Pickup Front Dropmember Coilover suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 1 Front will set the bottom of the cab approx. 7-9" inches off the ground at ride height.
The 1973-87 Chevy Pickup Rear Level 3 Airbag Dropmember suspension system is engineered to lay frame with large diameter wheel/tire combinations.
The 1973-87 Chevy Pickup Front Dropmember Coilover suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 2 Front will set the bottom of the cab approx. 4-6" inches off the ground at ride height.
The Dropmember Level 3 61-64 Ford F100 Front suspension system is a modular bolt-in sub-frame assembly engineered to incorporate Porterbuilt and C10 based suspension components.
When combined with a 2.5” drop spindle, 28” tall tire, and Porterbuilt Tubular Control Arms, the Level 3 Front will set the lowest point of the factory sheet metal on the ground when fully deflated.
The 1973-87 Chevy Pickup Rear Level 2 Coilover Dropmember suspension system is engineered to improve ride quality, performance, aesthetics, and strength.
The 1973-87 Chevy Pickup Rear Level 2 Coilover Dropmember suspension system is engineered to improve ride quality, performance, aesthetics, and strength.