This power rack and pinion from CPP is new, not a rebuilt or remanufactured rack.
Learn MoreThese stainless steel headers are used with the Porterbuilt Level 3 Dropmember (Version 5, 6 & 7) when doing an LS swap.
Learn MoreCompatible with Level 2 and Level 3 Dropmember equipped trucks running a BBC engine.
We DO NOT stock these headers. They can be purchased here:
http://www.summitracing.com/parts/hed-65103.
Compatible with Level 1-3 Dropmember equipped trucks running a SBC engine.
NOT COMPATIBLE WITH THE VERSION 7 DROPMEMBER.
We DO NOT stock these headers. They can be purchased here:
http://www.summitracing.com/parts/hok-2466hkr.
Product Number: 14038
Approx 19 Gallons
1973-87 Chevy C10
Standard
Bed Fill
Non-EFI
* Pictures may show optional accessories installed. Depending upon the options you choose your tank may vary slightly from shown.
Learn MoreProduct Number: 14039
Approx 19 Gallons
1973-87 Chevy C10
Standard
Side Fill
Non-EFI
* Pictures may show optional accessories installed. Depending upon the options you choose your tank may vary slightly from shown.
Learn MoreProduct Number: 14040
Approx 19 Gallons
1973-87 Chevy C10
Side Fill
Aeromotive In-Tank Pump
The new Porterbuilt sway bar is manufactured in-house and is available for Version 7 Dropmember equipped trucks. It comes raw and includes all mounting hardware.
Learn MoreThe 1973-87 Chevy Pickup Front Dropmember suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 1 Front will the lowest point of the factory frame rails approx. 3” off the ground when fully deflated.
The 1973-87 Chevy Pickup Rear Level 1 Airbag Dropmember suspension system is designed to replace the factory components and improve ride quality, performance, aesthetics, and strength.
The 1973-87 Chevy Pickup Rear Level 2 Coilover Dropmember suspension system is engineered to improve ride quality, performance, aesthetics, and strength.
The 1973-87 Chevy Pickup Rear Level 2 Coilover Dropmember suspension system is engineered to improve ride quality, performance, aesthetics, and strength.
New Boxed Inner Frame Stiffener for Level 2 & Level 3 Dropmember Equipped Trucks
The new Porterbuilt sway bar is manufactured in-house and is available for trucks equipped with PB Fab control arms and the factory crossmember. It comes raw and includes all mounting hardware.
Learn MorePerformance Power Rack & Pinion for all Dropmember applications.
Learn MoreThe new Porterbuilt sway bar is manufactured in-house and is available for early Dropmember equipped trucks. It comes raw and includes all mounting hardware.
Learn MoreWilwood Forged Narrow Superlite 6R Front Brake Kit
14" Rotors, Drilled & Slotted Available
6 Piston Calipers, Red or Black Available
18" Minimum Wheel Diameter
* FOR USE WITH CPP MODULAR SPINDLES
Learn MoreWilwood Forged Narrow Superlite 6R Front Brake Kit
13.06" Rotors, Drilled & Slotted Available
6 Piston Calipers, Red or Black Available
17" Minimum Wheel Diameter
* FOR USE WITH CPP MODULAR SPINDLES
Learn MoreWilwood Forged Narrow Superlite 6R Front Brake Kit
6 Lug
14" Rotors, Drilled & Slotted Available
6 Piston Calipers, Red or Black Available
18" Minimum Wheel Diameter
* FOR USE WITH CPP MODULAR SPINDLES
Learn MoreWilwood Forged Narrow Superlite 6R Front Brake Kit
6 Lug
13.06" Rotors, Drilled & Slotted Available
6 Piston Calipers, Red or Black Available
17" Minimum Wheel Diameter
* FOR USE WITH CPP MODULAR SPINDLES
Learn MoreWilwood Forged Narrow Superlite 6R Front Brake Kit
12.19" Rotors, SRP Drilled & Slotted Available
6 Piston Calipers, Red or Black Available
15" Minimum Wheel Diameter
* FOR USE WITH WILWOOD C10 PRO SPINDLES
Learn MoreWilwood Forged Narrow Superlite 6R Front Brake Kit
13.06" Rotors, SRP Drilled & Slotted Available
6 Piston Calipers, Red or Black Available
17" Minimum Wheel Diameter
* FOR USE WITH WILWOOD C10 PRO SPINDLES
Learn MoreWilwood Forged Narrow Superlite 6R Front Brake Kit
14" Rotors, SRP Drilled & Slotted Available
6 Piston Calipers, Red or Black Available
18" Minimum Wheel Diameter
* FOR USE WITH WILWOOD C10 PRO SPINDLES
Learn MoreWilwood Forged Narrow Superlite 6R Front Brake Kit
14" Rotors, SRP Drilled & Slotted Available
6 Piston Calipers, Red or Black Available
18" Minimum Wheel Diameter
* FOR USE WITH WILWOOD C10 STEEL SPINDLES
Learn MoreWilwood Forged Narrow Superlite 6R Front Brake Kit
13" Rotors, SRP Drilled & Slotted Available
6 Piston Calipers, Red or Black Available
17" Minimum Wheel Diameter
* FOR USE WITH WILWOOD C10 STEEL SPINDLES
Learn MoreWilwood Forged Narrow Superlite 6R Front Brake Kit
6 Lug
14" Rotors, SRP Drilled & Slotted Available
6 Piston Calipers, Red or Black Available
18" Minimum Wheel Diameter
* FOR USE WITH WILWOOD C10 STEEL SPINDLES
Learn MoreWilwood Forged Narrow Superlite 6R Front Brake Kit
6 Lug
13" Rotors, SRP Drilled & Slotted Available
6 Piston Calipers, Red or Black Available
17" Minimum Wheel Diameter
* FOR USE WITH WILWOOD C10 STEEL SPINDLES
Learn MoreWilwood Forged Narrow Superlite 6R Front Brake Kit
12" 1 Piece Rotor and Hats, SRP Drilled & Slotted Available
6 Piston Calipers, Red or Black Available
15" Minimum Wheel Diameter
* FOR USE WITH WILWOOD C10 STEEL SPINDLES
Learn MoreWilwood Forged Narrow Superlite 6R Front Brake Kit
6 Lug
12" 1 Piece Rotor and Hats, SRP Drilled & Slotted Available
6 Piston Calipers, Red or Black Available
15" Minimum Wheel Diameter
* FOR USE WITH WILWOOD C10 STEEL SPINDLES
Learn MoreTHESE CONTROL ARMS ARE FOR VERSION 7, COILOVER DROPMEMBER APPLICATIONS ONLY.
Porterbuilt tubular control arms are built using thick-wall DOM tubing and CNC cut 3/16" pickeled plate steel. All bushing pivot tubes and ball joint cups are TIG welded.
Includes shafts, bushings, and Grade 8 hardware for installation.
NOTE: ALL CONTROL ARMS ARE DESIGNED TO USE PROFORGED BALL JOINTS. .
Learn MoreTHESE CONTROL ARMS ARE FOR VERSION 7 DROPMEMBER APPLICATIONS ONLY.
Porterbuilt tubular control arms are built using thick-wall DOM tubing and CNC cut 3/16" pickeled plate steel. All bushing pivot tubes and ball joint cups are TIG welded.
Includes shafts, bushings, and Grade 8 hardware for installation.
NOTE: ALL CONTROL ARMS ARE DESIGNED TO USE PROFORGED BALL JOINTS. .
Learn MoreThe 1973-87 Chevy Pickup Front Dropmember suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 3 Front will set the lowest point of the factory frame rails on the ground when fully deflated.
The 1973-87 Chevy Pickup Rear Level 3 Airbag Dropmember suspension system is engineered to lay frame with large diameter wheel/tire combinations.
The 1973-87 Chevy Pickup Front Dropmember Coilover suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 1 Front will set the bottom of the cab approx. 7-9" inches off the ground at ride height.
The 1973-87 Chevy Pickup Front Dropmember Coilover suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 2 Front will set the bottom of the cab approx. 4-6" inches off the ground at ride height.
THESE CONTROL ARMS ARE FOR EARLY (PRE VERSION 7) DROPMEMBER APPLICATIONS ONLY.
Porterbuilt tubular control arms are built using thick-wall DOM tubing and CNC cut 3/16" pickeled plate steel. All bushing pivot tubes and ball joint cups are TIG welded.
Includes shafts, bushings, and Grade 8 hardware for installation.
NOTE: ALL CONTROL ARMS ARE DESIGNED TO USE PROFORGED BALL JOINTS. .
Learn MorePorterbuilt tubular control arms are built using thick-wall DOM tubing and CNC cut 3/16" pickeled plate steel. All bushing pivot tubes and ball joint cups are TIG welded.
Available in the following configurations:
1" Forward
1" Narrowed
1" Forward & 1" Narrowed
Standard Length
Includes upper and lower shafts, bushings, and Grade 8 hardware for installation.
NOTE: ALL CONTROL ARMS ARE DESIGNED TO USE PROFORGED BALL JOINTS. .
Learn MoreTubular rear frame crossmember built using thick-wall 1.5" tubing & 3/16" steel.
Tubular core support crossmember built using thick-wall 1.5" tubing & 3/16" steel.