Search results for: 'Hood hinge installation 69 chevy c10'

New Boxed Inner Frame Stiffener for Level 2 & Level 3 Dropmember Equipped Trucks

Fits: 1963-72 Dropmember Equipped Chevy Trucks

New Boxed Inner Frame Stiffener for Level 2 & Level 3 Dropmember Equipped Trucks

Fits: 1947-54 Dropmember Equipped Chevy Trucks

New Boxed Inner Frame Stiffener for Level 2 & Level 3 Dropmember Equipped Trucks

Fits: 1955-59 Dropmember Equipped Chevy Trucks

Wilwood Forged Narrow Superlite 6R Front Brake Kit
12" 1 Piece Rotor and Hats, SRP Drilled & Slotted Available
6 Piston Calipers, Red or Black Available
15" Minimum Wheel Diameter

* FOR USE WITH WILWOOD C10 STEEL SPINDLES

New Boxed Inner Frame Stiffener for Level 1 Dropmember, Static & Stock Suspension Trucks

Fits: 1963-72 Chevy Trucks

Wilwood Forged Narrow Superlite 6R Front Brake Kit
6 Lug
12" 1 Piece Rotor and Hats, SRP Drilled & Slotted Available
6 Piston Calipers, Red or Black Available
15" Minimum Wheel Diameter

* FOR USE WITH WILWOOD C10 STEEL SPINDLES

If you are thinking about lowering your C10 truck more than four inches in the rear, a longer trac-bar will be a necessity! The Porterbuilt Fully Adjustable Trac-bar has an overall length of just over 34 inches. The longer the bar, the less side to side shift the differential will experience through suspension travel. The new mounting brackets also relocate the bar lowering the rear roll-center, and the bar length can be tuned while still mounted on the truck!

The Porterbuilt Stage 2 Rear “Deluxe” Kit for 63-72 C10 is an engineered bolt-in suspension system designed to lower your truck as low as possible while maintaining the factory bed floor. The Stage 2 “Deluxe” is just that, it replaces all the factory crossmembers (from the trailing arm cross-member back) with tubular versions that are designed to bolt right in! It also includes our fully adjustable trac bar for improved handling and performance. If you are looking for the best possible kit to lower your C10 and keep the bed-floor in tact… this is the one!

THESE CONTROL ARMS ARE FOR VERSION 7, COILOVER DROPMEMBER APPLICATIONS ONLY.

Porterbuilt tubular control arms are built using thick-wall DOM tubing and CNC cut 3/16" pickeled plate steel. All bushing pivot tubes and ball joint cups are TIG welded.

Includes shafts, bushings, and Grade 8 hardware for installation.

NOTE: ALL CONTROL ARMS ARE DESIGNED TO USE PROFORGED BALL JOINTS. .

THESE CONTROL ARMS ARE FOR VERSION 7 DROPMEMBER APPLICATIONS ONLY.

Porterbuilt tubular control arms are built using thick-wall DOM tubing and CNC cut 3/16" pickeled plate steel. All bushing pivot tubes and ball joint cups are TIG welded.

Includes shafts, bushings, and Grade 8 hardware for installation.

NOTE: ALL CONTROL ARMS ARE DESIGNED TO USE PROFORGED BALL JOINTS. .

THESE CONTROL ARMS ARE FOR EARLY (PRE VERSION 7) DROPMEMBER APPLICATIONS ONLY.

Porterbuilt tubular control arms are built using thick-wall DOM tubing and CNC cut 3/16" pickeled plate steel. All bushing pivot tubes and ball joint cups are TIG welded.

Includes shafts, bushings, and Grade 8 hardware for installation.

NOTE: ALL CONTROL ARMS ARE DESIGNED TO USE PROFORGED BALL JOINTS. .

The Dropmember Level 3 61-64 Ford F100 Front suspension system is a modular bolt-in sub-frame assembly engineered to incorporate Porterbuilt and C10 based suspension components.
When combined with a 2.5” drop spindle, 28” tall tire, and Porterbuilt Tubular Control Arms, the Level 3 Front will set the lowest point of the factory sheet metal on the ground when fully deflated.

Porterbuilt tubular control arms are built using thick-wall DOM tubing and CNC cut 3/16" pickeled plate steel. All bushing pivot tubes and ball joint cups are TIG welded.

Available in the following configurations:
1" Forward
1" Narrowed
1" Forward & 1" Narrowed
Standard Length

Includes upper and lower shafts, bushings, and Grade 8 hardware for installation.

NOTE: ALL CONTROL ARMS ARE DESIGNED TO USE PROFORGED BALL JOINTS. .

The Porterbuilt Stage 2 Basic Front Kit for '63-'87 Chevy Trucks improves ride quality and overall driveability by replacing the factory lower control arms and and factory coil spring with an air spring.

Tubular panhard bar crossmember built using thick-wall 1.5" tubing & 3/16" steel.

Fits: 1963-72 Chevy Trucks

Boxed carrier bearing crossmember built using 3/16" steel.

Fits: 1973-87 Chevy Trucks

If you are looking for the best possible kit to convert your truck to air suspension but maintain your factory front crossmember, this is the kit for you. The Porterbuilt Stage 2 Deluxe Front Kit for '63-'87 Chevy Trucks replaces your factory control arms and coil springs, lowering your truck and improving handling, without replacing the factory front crossmember.

New boxed rear frame crossmember fabricated from 3/16" steel.

Fits: 1973-87 Chevy Trucks

Tubular carrier bearing crossmember built using thick-wall 1.5" tubing & 3/16" steel.

Fits: 1963-72 Chevy Trucks

New boxed rear frame crossmember fabricated from 3/16" steel.

Fits: 1963-72 Chevy Trucks

Tubular rear frame crossmember built using thick-wall 1.5" tubing & 3/16" steel.

Fits: 1955-59 Chevy Trucks

Tubular rear frame crossmember built using thick-wall 1.5" tubing & 3/16" steel.

Fits: 1960-62 Chevy Trucks

Tubular rear frame crossmember built using thick-wall 1.5" tubing & 3/16" steel.

Fits: 1973-87 Chevy Trucks

Boxed Trailing Arm Crossmember built using 3/16" steel for a 2-piece driveshaft configuration.

Fits: 1955-59 Chevy Trucks

Tubular trailing arm crossmember built using thick-wall 1.5" tubing & 3/16" steel.

Fits: 1963-72 Chevy Trucks

Tubular trailing arm crossmember built using thick-wall 1.5" tubing & 3/16" steel.

Fits: 1963-72 Chevy Trucks

Tubular rear frame crossmember built using thick-wall 1.5" tubing & 3/16" steel.

Fits: 1963-72 Chevy Trucks

Tubular trailing arm crossmember built using thick-wall 1.5" tubing & 3/16" steel.

Fits: 1963-72 Chevy Trucks

These stainless steel headers are used with the Porterbuilt Level 3 Dropmember (Version 5, 6 & 7) when doing an LS swap.

The Porterbuilt Bolt-on Body Drop for the 1967-1972 C10 is for those guys who just can’t be low enough! It is designed to make it easier to set the pinch weld level to the bottom of the frame.

Boxed trailing arm crossmember built using 3/16" steel.

Fits: 1963-72 Chevy Trucks

Boxed trailing arm crossmember built using 3/16" steel.

Fits: 1963-72 Chevy Trucks

This standard Firestone air spring offers maximum load support and operates at up to 100 psi. The spring has a 1/4" inflation port, a ride height of 8.25" and a maximum diameter of 5.70".

* Includes 2 air springs

All Viair 444C compressors feature a head assembly that includes a newly-developed, patents pending intercooler head. Additionally, they are equipped with a stainless steel braided leader hose with inline check valve assembly that serves to protect the compressor by eliminating the possibility of high amperage restarts.

Air Lift Performance 3H combines pressure-based control with ride-height sensing technology. While both types of air management have been utilized before, this is the first product to harness the benefits of both sytems – instantly improving suspension control, performance, and vehicle ride flexibility.

NOTE: As of April 2024, all 3H and 3P manifolds come with 1/4" threaded FNPT ports.

Air Lift Performance 3P combines pressure-based control with the ability to add ride-height sensing technology with the upgrade to height sensors. While both types of air management have been utilized before, this is the first product to harness the benefits of both sytems – instantly improving suspension control, performance, and vehicle ride flexibility.

NOTE: As of April 2024, all 3H and 3P manifolds come with 1/4" threaded FNPT ports. 

The new Porterbuilt sway bar is manufactured in-house and is available for early Dropmember equipped trucks. It comes raw and includes all mounting hardware.

The stage 1 rear kit is both an economical and easy way to lower the rear of your 63-72 C10′s trailing arm suspension. The air spring and mounting plates replace the factory steel coil spring, allowing a better ride quality and adjustability! Our Stage 1 shock relocator brackets improve shock function by decreasing the shock angle!

The new Porterbuilt sway bar is manufactured in-house and is available for trucks equipped with PB Fab control arms and the factory crossmember. It comes raw and includes all mounting hardware.

Wilwood Forged Narrow Superlite 6R Front Brake Kit
14" Rotors, Drilled & Slotted Available
6 Piston Calipers, Red or Black Available
18" Minimum Wheel Diameter

* FOR USE WITH CPP MODULAR SPINDLES

Wilwood Forged Narrow Superlite 6R Front Brake Kit
13.06" Rotors, Drilled & Slotted Available
6 Piston Calipers, Red or Black Available
17" Minimum Wheel Diameter

* FOR USE WITH CPP MODULAR SPINDLES

Wilwood Forged Narrow Superlite 6R Front Brake Kit
6 Lug
14" Rotors, Drilled & Slotted Available
6 Piston Calipers, Red or Black Available
18" Minimum Wheel Diameter

* FOR USE WITH CPP MODULAR SPINDLES

Wilwood Forged Narrow Superlite 6R Front Brake Kit
6 Lug
13.06" Rotors, Drilled & Slotted Available
6 Piston Calipers, Red or Black Available
17" Minimum Wheel Diameter

* FOR USE WITH CPP MODULAR SPINDLES

The Porterbuilt Stage 2 Rear “Deluxe” Kit for 63-72 C10 is an engineered bolt-in suspension system designed to lower your truck as low as possible while maintaining the factory bed floor. The Stage 2 “Deluxe” is just that, it replaces all the factory crossmembers (from the trailing arm cross-member back) with tubular versions that are designed to bolt right in! It also includes our fully adjustable trac bar for improved handling and performance. If you are looking for the best possible kit to lower your C10 and keep the bed-floor in tact… this is the one!

Compatible with Level 2 and Level 3 Dropmember equipped trucks running a BBC engine.

We DO NOT stock these headers. They can be purchased here:
http://www.summitracing.com/parts/hed-65103.

Compatible with Level 1-3 Dropmember equipped trucks running a SBC engine.

NOT COMPATIBLE WITH THE VERSION 7 DROPMEMBER.

We DO NOT stock these headers. They can be purchased here:
http://www.summitracing.com/parts/hok-2466hkr.