Product Number: 14003
Approx 19 Gallons
1963-72 Chevy C10
Side Fill
Aeromotive In-Tank Pump
The Dropmember Level 3 61-64 Ford F100 Front suspension system is a modular bolt-in sub-frame assembly engineered to incorporate Porterbuilt and C10 based suspension components.
When combined with a 2.5” drop spindle, 28” tall tire, and Porterbuilt Tubular Control Arms, the Level 3 Front will set the lowest point of the factory sheet metal on the ground when fully deflated.
Product Number: 14002
Approx 19 Gallons
1963-72 Chevy C10
Standard
Side Fill
Non-EFI
* Shown With Optional Rollover Vent and Sending Unit Installed.
Learn MoreProduct Number: 14001
Approx 19 Gallons
1963-72 Chevy C10
Standard
Bed Fill
Non-EFI
* Shown With Optional Rollover Vent and Sending Unit Installed.
Learn MoreNew Inner Frame Stiffener for Level 2 & Level 3 Dropmember Equipped Trucks
New Boxed Inner Frame Stiffener for Level 2 & Level 3 Dropmember Equipped Trucks
New Boxed Inner Frame Stiffener for Level 2 & Level 3 Dropmember Equipped Trucks
New Boxed Inner Frame Stiffener for Level 2 & Level 3 Dropmember Equipped Trucks
New Boxed Inner Frame Stiffener for Level 2 & Level 3 Dropmember Equipped Trucks
New Boxed Inner Frame Stiffener for Level 1 Dropmember, Static & Stock Suspension Trucks
The Porterbuilt Stage 2 Basic Front Kit for '63-'87 Chevy Trucks improves ride quality and overall driveability by replacing the factory lower control arms and and factory coil spring with an air spring.
Learn MoreIf you are looking for the best possible kit to convert your truck to air suspension but maintain your factory front crossmember, this is the kit for you. The Porterbuilt Stage 2 Deluxe Front Kit for '63-'87 Chevy Trucks replaces your factory control arms and coil springs, lowering your truck and improving handling, without replacing the factory front crossmember.
Learn MoreThese stainless steel headers are used with the Porterbuilt Level 3 Dropmember (Version 5, 6 & 7) when doing an LS swap.
Learn MoreTubular trailing arm crossmember built using thick-wall 1.5" tubing & 3/16" steel.
The Porterbuilt Stage 2 Rear “Deluxe” Kit for 63-72 C10 is an engineered bolt-in suspension system designed to lower your truck as low as possible while maintaining the factory bed floor. The Stage 2 “Deluxe” is just that, it replaces all the factory crossmembers (from the trailing arm cross-member back) with tubular versions that are designed to bolt right in! It also includes our fully adjustable trac bar for improved handling and performance. If you are looking for the best possible kit to lower your C10 and keep the bed-floor in tact… this is the one!
Learn MoreTubular trailing arm crossmember built using thick-wall 1.5" tubing & 3/16" steel.
Tubular trailing arm crossmember built using thick-wall 1.5" tubing & 3/16" steel.
Tubular carrier bearing crossmember built using thick-wall 1.5" tubing & 3/16" steel.
Tubular rear frame crossmember built using thick-wall 1.5" tubing & 3/16" steel.
Tubular rear frame crossmember built using thick-wall 1.5" tubing & 3/16" steel.
Tubular rear frame crossmember built using thick-wall 1.5" tubing & 3/16" steel.
Boxed Trailing Arm Crossmember built using 3/16" steel for a 2-piece driveshaft configuration.
Tubular rear frame crossmember built using thick-wall 1.5" tubing & 3/16" steel.
Product Number: 14040
Approx 19 Gallons
1973-87 Chevy C10
Side Fill
Aeromotive In-Tank Pump
The new Porterbuilt sway bar is manufactured in-house and is available for Version 7 Dropmember equipped trucks. It comes raw and includes all mounting hardware.
Learn MoreThe stage 1 rear kit is both an economical and easy way to lower the rear of your 63-72 C10′s trailing arm suspension. The air spring and mounting plates replace the factory steel coil spring, allowing a better ride quality and adjustability! Our Stage 1 shock relocator brackets improve shock function by decreasing the shock angle!
Learn MoreTubular panhard bar crossmember built using thick-wall 1.5" tubing & 3/16" steel.
The Porterbuilt Bolt-on Body Drop for the 1967-1972 C10 is for those guys who just can’t be low enough! It is designed to make it easier to set the pinch weld level to the bottom of the frame.
Learn MoreTubular core support crossmember built using thick-wall 1.5" tubing & 3/16" steel.
Looking for an easy way to switch over to air suspension without breaking the bank? The Stage 1 front kit is an inexpensive and simple way to do just that! The Stage 1 front kit is designed to replace the factory steel coil spring with an air spring while maintaining the factory control arms.
NOTE: ALL CONTROL ARMS ARE DESIGNED TO USE PROFORGED BALL JOINTS. .
Learn More1967-72 Longbed to Shortbed Conversion Kit
Includes templates and c-channel supports
Available for C10 and C20 trucks
Welding is required Learn More
Air Lift Performance 3H combines pressure-based control with ride-height sensing technology. While both types of air management have been utilized before, this is the first product to harness the benefits of both sytems – instantly improving suspension control, performance, and vehicle ride flexibility.
NOTE: As of April 2024, all 3H and 3P manifolds come with 1/4" threaded FNPT ports.
Learn More16" Big Brake Kit From Little Shop Manufacturing
Available with Wilwood 6 Piston Calipers or MFG 6 Piston Calipers
Comes with Drilled & Slotted Rotors
FITS WILWOOD ALUMINUM PROSPINDLE ONLY (NOT INCLUDED)
Learn MoreCompatible with Level 2 and Level 3 Dropmember equipped trucks running a BBC engine.
We DO NOT stock these headers. They can be purchased here:
http://www.summitracing.com/parts/hed-65103.
Compatible with Level 1-3 Dropmember equipped trucks running a SBC engine.
NOT COMPATIBLE WITH THE VERSION 7 DROPMEMBER.
We DO NOT stock these headers. They can be purchased here:
http://www.summitracing.com/parts/hok-2466hkr.
The Porterbuilt Stage 2 Rear “Deluxe” Kit for 63-72 C10 is an engineered bolt-in suspension system designed to lower your truck as low as possible while maintaining the factory bed floor. The Stage 2 “Deluxe” is just that, it replaces all the factory crossmembers (from the trailing arm cross-member back) with tubular versions that are designed to bolt right in! It also includes our fully adjustable trac bar for improved handling and performance. If you are looking for the best possible kit to lower your C10 and keep the bed-floor in tact… this is the one!
Learn MoreOur PB Fab custom built full frames are available for a variety of trucks. Each frame is custom built, hand welded and hand metal finished specifically for you.
Learn More