Search results for: 'trail width'

Tubular trailing arm crossmember built using thick-wall 1.5" tubing & 3/16" steel.

Fits: 1963-72 Chevy Trucks

Boxed Trailing Arm Crossmember built using 3/16" steel for a 2-piece driveshaft configuration.

Fits: 1955-59 Chevy Trucks

Boxed trailing arm crossmember built using 3/16" steel.

Fits: 1963-72 Chevy Trucks

Tubular trailing arm crossmember built using thick-wall 1.5" tubing & 3/16" steel.

Fits: 1963-72 Chevy Trucks

Tubular trailing arm crossmember built using thick-wall 1.5" tubing & 3/16" steel.

Fits: 1963-72 Chevy Trucks

Boxed trailing arm crossmember built using 3/16" steel.

Fits: 1963-72 Chevy Trucks

The stage 1 rear kit is both an economical and easy way to lower the rear of your 63-72 C10′s trailing arm suspension. The air spring and mounting plates replace the factory steel coil spring, allowing a better ride quality and adjustability! Our Stage 1 shock relocator brackets improve shock function by decreasing the shock angle!

The Porterbuilt Stage 2 Rear “Deluxe” Kit for 63-72 C10 is an engineered bolt-in suspension system designed to lower your truck as low as possible while maintaining the factory bed floor. The Stage 2 “Deluxe” is just that, it replaces all the factory crossmembers (from the trailing arm cross-member back) with tubular versions that are designed to bolt right in! It also includes our fully adjustable trac bar for improved handling and performance. If you are looking for the best possible kit to lower your C10 and keep the bed-floor in tact… this is the one!

New Boxed Inner Frame Stiffener for Level 2 & Level 3 Dropmember Equipped Trucks

Fits: 1963-72 Dropmember Equipped Chevy Trucks

New Boxed Inner Frame Stiffener for Level 2 & Level 3 Dropmember Equipped Trucks

Fits: 1947-54 Dropmember Equipped Chevy Trucks

New Boxed Inner Frame Stiffener for Level 1 Dropmember, Static & Stock Suspension Trucks

Fits: 1963-72 Chevy Trucks

The 1963-72 Chevy Blazer 2WD Rear Level 3 Airbag Dropmember suspension system is engineered to lay frame with large diameter wheel/tire combinations.

Ride Height - 4"
Deflated Height - Lay Frame

The 1963-72 Chevy Blazer 4WD Rear Level 3 Airbag Dropmember suspension system is engineered to lay frame with large diameter wheel/tire combinations.

Ride Height - 4"
Deflated Height - Lay Frame

The 1963-72 Chevy Pickup Rear Level 3 Airbag Dropmember suspension system is engineered to lay frame with large diameter wheel/tire combinations.

Ride Height - 4"
Deflated Height - Lay Frame

The 1963-72 Chevy Pickup Rear Level 1 Airbag Dropmember suspension system is designed to replace the factory components and improve ride quality, performance, aesthetics, and strength.

Ride Height - 7"
Deflated Height - 3"

The Porterbuilt cowl mounted hood hinges are the perfect solution to relocating the hood hinges once the factory inner fender wells have been removed. They are available for model years 1960-1972.

The 1963-72 Chevy Pickup Rear Level 2 Coilover Dropmember suspension system is engineered to improve ride quality, performance, aesthetics, and strength.

Ride Height - 4-6"

The 1963-72 Chevy Pickup Rear Level 2 Coilover Dropmember suspension system is engineered to improve ride quality, performance, aesthetics, and strength.

Ride Height - 7-9"

New Boxed Inner Frame Stiffener for Level 2 & Level 3 Dropmember Equipped Trucks

Fits: 1973-87 Chevy Trucks

The Porterbuilt cowl mounted hood hinges are the perfect solution to relocating the hood hinges once the factory inner fender wells have been removed. They are available for model years 1960-1972.

1967-72 Longbed to Shortbed Conversion Kit
Includes templates and c-channel supports
Available for C10 and C20 trucks
Welding is required Learn More

Air Lift Performance 3H combines pressure-based control with ride-height sensing technology. While both types of air management have been utilized before, this is the first product to harness the benefits of both sytems – instantly improving suspension control, performance, and vehicle ride flexibility.

NOTE: As of April 2024, all 3H and 3P manifolds come with 1/4" threaded FNPT ports.

Air Lift Performance 3P combines pressure-based control with the ability to add ride-height sensing technology with the upgrade to height sensors. While both types of air management have been utilized before, this is the first product to harness the benefits of both sytems – instantly improving suspension control, performance, and vehicle ride flexibility.

NOTE: As of April 2024, all 3H and 3P manifolds come with 1/4" threaded FNPT ports. 

The 1960-62 Chevy Pickup Front Dropmember Coilover suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 2 Front Coilover system will set the lowest point of the factory frame rails approx. 5-6" inches off the ground at ride height.

Ride Height - 5-6"

The 1973-87 Chevy Pickup Rear Level 1 Airbag Dropmember suspension system is designed to replace the factory components and improve ride quality, performance, aesthetics, and strength.

Ride Height - 7"
Deflated Height - 3"

The 1963-72 Chevy Pickup Front Dropmember Coilover suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 2 Front will set the bottom of the cab approx. 4-6" inches off the ground at ride height.

Ride Height - 4-6"

The 1963-72 Chevy Pickup Front Dropmember Coilover suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 1 Front will set the bottom of the cab approx. 7-9" inches off the ground at ride height.

Ride Height - 7-9"

The 1973-87 Chevy Pickup Front Dropmember Coilover suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 1 Front will set the bottom of the cab approx. 7-9" inches off the ground at ride height.

Ride Height - 7-9"

The 1973-87 Chevy Pickup Front Dropmember Coilover suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 2 Front will set the bottom of the cab approx. 4-6" inches off the ground at ride height.

Ride Height - 4-6"

The 1960-62 Chevy Pickup Front Dropmember suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 3 Front will set the lowest point of the factory frame rails on the ground when fully deflated.

Ride Height - 4"
Deflated Height - Lay Frame

The 1963-72 Chevy Pickup Front Dropmember suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 3 Front will set the lowest point of the factory frame rails on the ground when fully deflated.

Ride Height - 4"
Deflated Height - Lay Frame

The 1963-72 Chevy Pickup Front Dropmember suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 1 Front will the lowest point of the factory frame rails approx. 3” off the ground when fully deflated.

Ride Height - 6-7"
Deflated Height - 3"

The 1973-87 Chevy Pickup Front Dropmember suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 1 Front will the lowest point of the factory frame rails approx. 3” off the ground when fully deflated.

Ride Height - 6-7"
Deflated Height - 3"

The 1973-87 Chevy Pickup Front Dropmember suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 3 Front will set the lowest point of the factory frame rails on the ground when fully deflated.

Ride Height - 4"
Deflated Height - Lay Frame

The Dropmember Rear Back Half suspension system is engineered fit 12" wide wheels.
Fits 1960-62 C10 Trucks
Level 2, Touring
Ride height measures approx. 5” when running a 30” tall tire.

DESIGNED FOR 12" WIDE WHEELS
LONG BED TO SHORT BED CONVERSION

The Dropmember Rear Back Half suspension system is engineered fit 12-15" wide wheels.
Fits 1963-72 C10 Trucks
Level 2, Touring
Ride height measures approx. 5” when running a 30” tall tire.

DESIGNED FOR 12"-15" WIDE WHEELS
LONG BED TO SHORT BED CONVERSION

The Dropmember Rear Back Half suspension system is engineered to lay frame with 12" wide wheels.
Fits 1960-62 C10 Trucks
Level 3, Extreme
Ride height measures approx. 5” when running a 30” tall tire, and the frame will rest on the ground when deflated.

DESIGNED FOR 12" WIDE WHEELS
LONG BED TO SHORT BED CONVERSION

The Dropmember Rear Back Half suspension system is engineered to lay frame with 12-15" wide wheels.
Fits 1963-72 C10 Trucks
Level 3, Extreme
Ride height measures approx. 5” and the frame will rest on the ground when deflated.

DESIGNED FOR 12"-15" WIDE WHEELS
LONG BED TO SHORT BED CONVERSION

Product Number: 14001
Approx 19 Gallons

1963-72 Chevy C10
Standard
Bed Fill
Non-EFI

* Shown With Optional Rollover Vent and Sending Unit Installed.

The Porterbuilt Stage 2 Rear “Deluxe” Kit for 63-72 C10 is an engineered bolt-in suspension system designed to lower your truck as low as possible while maintaining the factory bed floor. The Stage 2 “Deluxe” is just that, it replaces all the factory crossmembers (from the trailing arm cross-member back) with tubular versions that are designed to bolt right in! It also includes our fully adjustable trac bar for improved handling and performance. If you are looking for the best possible kit to lower your C10 and keep the bed-floor in tact… this is the one!