Search results for: 'Gas tank'

Product Number: 14038
Approx 19 Gallons

1973-87 Chevy C10
Standard
Bed Fill
Non-EFI

* Pictures may show optional accessories installed. Depending upon the options you choose your tank may vary slightly from shown.

Product Number: 14039
Approx 19 Gallons

1973-87 Chevy C10
Standard
Side Fill
Non-EFI

* Pictures may show optional accessories installed. Depending upon the options you choose your tank may vary slightly from shown.

Product Number: 14004
Approx 19 Gallons

1963-72 Chevy C10
Bed Fill
Aeromotive In-Tank Pump

Product Number: 14003
Approx 19 Gallons

1963-72 Chevy C10
Side Fill
Aeromotive In-Tank Pump

Product Number: 14040
Approx 19 Gallons

1973-87 Chevy C10
Bed Fill
Aeromotive In-Tank Pump

Product Number: 14040
Approx 19 Gallons

1973-87 Chevy C10
Side Fill
Aeromotive In-Tank Pump

Product Number: 14002
Approx 19 Gallons

1963-72 Chevy C10
Standard
Side Fill
Non-EFI

* Shown With Optional Rollover Vent and Sending Unit Installed.

Product Number: 14001
Approx 19 Gallons

1963-72 Chevy C10
Standard
Bed Fill
Non-EFI

* Shown With Optional Rollover Vent and Sending Unit Installed.

New boxed rear frame crossmember fabricated from 3/16" steel.

Fits: 1973-87 Chevy Trucks

Tubular rear frame crossmember built using thick-wall 1.5" tubing & 3/16" steel.

Fits: 1955-59 Chevy Trucks

Tubular rear frame crossmember built using thick-wall 1.5" tubing & 3/16" steel.

Fits: 1960-62 Chevy Trucks

Tubular rear frame crossmember built using thick-wall 1.5" tubing & 3/16" steel.

Fits: 1973-87 Chevy Trucks

New boxed rear frame crossmember fabricated from 3/16" steel.

Fits: 1963-72 Chevy Trucks

Tubular rear frame crossmember built using thick-wall 1.5" tubing & 3/16" steel.

Fits: 1963-72 Chevy Trucks

The 1947-54 Chevy Pickup Rear Dropmember suspension system is engineered to lay body with large diameter wheel/tire combinations. (Recommended to run no wider than a 10” wheel)

Ride Height - 4"
Deflated Height - Lay Body

The 1960-62 Chevy Pickup Rear Dropmember suspension system is engineered to lay body with large diameter wheel/tire combinations. (Recommended to run no wider than a 10” wheel)

Ride Height - 4"
Deflated Height - Lay Body"

The 1963-72 Chevy Blazer 2WD Rear Level 3 Airbag Dropmember suspension system is engineered to lay frame with large diameter wheel/tire combinations.

Ride Height - 4"
Deflated Height - Lay Frame

The 1963-72 Chevy Blazer 4WD Rear Level 3 Airbag Dropmember suspension system is engineered to lay frame with large diameter wheel/tire combinations.

Ride Height - 4"
Deflated Height - Lay Frame

The 1973-87 Chevy Pickup Rear Level 3 Airbag Dropmember suspension system is engineered to lay frame with large diameter wheel/tire combinations.

Ride Height - 4"
Deflated Height - Lay Frame

The 1963-72 Chevy Pickup Rear Level 3 Airbag Dropmember suspension system is engineered to lay frame with large diameter wheel/tire combinations.

Ride Height - 4"
Deflated Height - Lay Frame

The 1963-72 Chevy Pickup Rear Level 1 Airbag Dropmember suspension system is designed to replace the factory components and improve ride quality, performance, aesthetics, and strength.

Ride Height - 7"
Deflated Height - 3"

The 1973-87 Chevy Pickup Rear Level 1 Airbag Dropmember suspension system is designed to replace the factory components and improve ride quality, performance, aesthetics, and strength.

Ride Height - 7"
Deflated Height - 3"

The Dropmember Rear Back Half suspension system is engineered to lay frame with 12" wide wheels.
Fits 1960-62 C10 Trucks
Level 3, Extreme
Ride height measures approx. 5” when running a 30” tall tire, and the frame will rest on the ground when deflated.

DESIGNED FOR 12" WIDE WHEELS
LONG BED TO SHORT BED CONVERSION

The Dropmember Rear Back Half suspension system is engineered to lay frame with 12-15" wide wheels.
Fits 1963-72 C10 Trucks
Level 3, Extreme
Ride height measures approx. 5” and the frame will rest on the ground when deflated.

DESIGNED FOR 12"-15" WIDE WHEELS
LONG BED TO SHORT BED CONVERSION

The 1955-59 Chevy Pickup Front Dropmember suspension system is a modular bolt-in sub-frame assembly engineered to incorporate Porterbuilt and C10 based suspension components.
When combined with a 2.5” drop spindle, 28” tall tire, and Porterbuilt Tubular Control Arms, the Level 3 Front will set the lowest point of the factory sheet metal on the ground when fully deflated.

Ride Height - 4"
Deflated Height - Lay Frame

The 1947-54 Chevy Pickup Front Dropmember suspension system is a modular bolt-in sub-frame assembly engineered to incorporate Porterbuilt and C10 based suspension components.
When combined with a 2.5” drop spindle, 28” tall tire, and Porterbuilt Tubular Control Arms, the Level 3 Front will set the lowest point of the factory sheet metal on the ground when fully deflated.

Ride Height - 4"
Deflated Height - Lay Frame

The 1960-62 Chevy Pickup Front Dropmember suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 3 Front will set the lowest point of the factory frame rails on the ground when fully deflated.

Ride Height - 4"
Deflated Height - Lay Frame

The 1963-72 Chevy Pickup Front Dropmember suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 3 Front will set the lowest point of the factory frame rails on the ground when fully deflated.

Ride Height - 4"
Deflated Height - Lay Frame

The 1963-72 Chevy Pickup Front Dropmember suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 1 Front will the lowest point of the factory frame rails approx. 3” off the ground when fully deflated.

Ride Height - 6-7"
Deflated Height - 3"

The 1973-87 Chevy Pickup Front Dropmember suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 1 Front will the lowest point of the factory frame rails approx. 3” off the ground when fully deflated.

Ride Height - 6-7"
Deflated Height - 3"

The Dropmember Rear Back Half suspension system is engineered fit 12" wide wheels.
Fits 1960-62 C10 Trucks
Level 2, Touring
Ride height measures approx. 5” when running a 30” tall tire.

DESIGNED FOR 12" WIDE WHEELS
LONG BED TO SHORT BED CONVERSION

The Dropmember Rear Back Half suspension system is engineered fit 12-15" wide wheels.
Fits 1963-72 C10 Trucks
Level 2, Touring
Ride height measures approx. 5” when running a 30” tall tire.

DESIGNED FOR 12"-15" WIDE WHEELS
LONG BED TO SHORT BED CONVERSION