These stainless steel headers are used with the Porterbuilt Level 3 Dropmember (Version 5, 6 & 7) when doing an LS swap.
Learn MoreThe 1963-72 Chevy Pickup Front Dropmember suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 1 Front will the lowest point of the factory frame rails approx. 3” off the ground when fully deflated.
The 1973-87 Chevy Pickup Front Dropmember suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 1 Front will the lowest point of the factory frame rails approx. 3” off the ground when fully deflated.
Product Number: 14040
Approx 19 Gallons
1973-87 Chevy C10
Side Fill
Aeromotive In-Tank Pump
Tubular carrier bearing crossmember built using thick-wall 1.5" tubing & 3/16" steel.
The Dropmember Level 3 61-64 Ford F100 Front suspension system is a modular bolt-in sub-frame assembly engineered to incorporate Porterbuilt and C10 based suspension components.
When combined with a 2.5” drop spindle, 28” tall tire, and Porterbuilt Tubular Control Arms, the Level 3 Front will set the lowest point of the factory sheet metal on the ground when fully deflated.
Product Number: 14038
Approx 19 Gallons
1973-87 Chevy C10
Standard
Bed Fill
Non-EFI
* Pictures may show optional accessories installed. Depending upon the options you choose your tank may vary slightly from shown.
Learn MoreProduct Number: 14039
Approx 19 Gallons
1973-87 Chevy C10
Standard
Side Fill
Non-EFI
* Pictures may show optional accessories installed. Depending upon the options you choose your tank may vary slightly from shown.
Learn MoreProduct Number: 14003
Approx 19 Gallons
1963-72 Chevy C10
Side Fill
Aeromotive In-Tank Pump
Product Number: 14002
Approx 19 Gallons
1963-72 Chevy C10
Standard
Side Fill
Non-EFI
* Shown With Optional Rollover Vent and Sending Unit Installed.
Learn MoreProduct Number: 14001
Approx 19 Gallons
1963-72 Chevy C10
Standard
Bed Fill
Non-EFI
* Shown With Optional Rollover Vent and Sending Unit Installed.
Learn MoreThe Porterbuilt Stage 2 Rear “Deluxe” Kit for 63-72 C10 is an engineered bolt-in suspension system designed to lower your truck as low as possible while maintaining the factory bed floor. The Stage 2 “Deluxe” is just that, it replaces all the factory crossmembers (from the trailing arm cross-member back) with tubular versions that are designed to bolt right in! It also includes our fully adjustable trac bar for improved handling and performance. If you are looking for the best possible kit to lower your C10 and keep the bed-floor in tact… this is the one!
Learn MoreCompatible with Level 2 and Level 3 Dropmember equipped trucks running a BBC engine.
We DO NOT stock these headers. They can be purchased here:
http://www.summitracing.com/parts/hed-65103.
Our PB Fab custom built full frames are available for a variety of trucks. Each frame is custom built, hand welded and hand metal finished specifically for you.
Learn MoreCompatible with Level 1-3 Dropmember equipped trucks running a SBC engine.
NOT COMPATIBLE WITH THE VERSION 7 DROPMEMBER.
We DO NOT stock these headers. They can be purchased here:
http://www.summitracing.com/parts/hok-2466hkr.