Search results for: 'Frame For 1970 c/10'

Replacement hood hinge strut for older style Gas Assist Hood Hinge kits.

THIS STRUT WILL ONLY REPLACE PART # C16-23577

New Inner Frame Stiffener for Level 2 & Level 3 Dropmember Equipped Trucks

Fits: 1960-62 Dropmember Equipped Chevy Trucks

New Boxed Inner Frame Stiffener for Level 2 & Level 3 Dropmember Equipped Trucks

Fits: 1947-54 Dropmember Equipped Chevy Trucks

New Boxed Inner Frame Stiffener for Level 2 & Level 3 Dropmember Equipped Trucks

Fits: 1955-59 Dropmember Equipped Chevy Trucks

New Boxed Inner Frame Stiffener for Level 2 & Level 3 Dropmember Equipped Trucks

Fits: 1973-87 Chevy Trucks

New Boxed Inner Frame Stiffener for Level 2 & Level 3 Dropmember Equipped Trucks

Fits: 1963-72 Dropmember Equipped Chevy Trucks

New Boxed Inner Frame Stiffener for Level 1 Dropmember, Static & Stock Suspension Trucks

Fits: 1963-72 Chevy Trucks

Tubular rear frame crossmember built using thick-wall 1.5" tubing & 3/16" steel.

Fits: 1955-59 Chevy Trucks

Tubular rear frame crossmember built using thick-wall 1.5" tubing & 3/16" steel.

Fits: 1960-62 Chevy Trucks

Tubular rear frame crossmember built using thick-wall 1.5" tubing & 3/16" steel.

Fits: 1963-72 Chevy Trucks

New boxed rear frame crossmember fabricated from 3/16" steel.

Fits: 1973-87 Chevy Trucks

New boxed rear frame crossmember fabricated from 3/16" steel.

Fits: 1963-72 Chevy Trucks

Tubular rear frame crossmember built using thick-wall 1.5" tubing & 3/16" steel.

Fits: 1973-87 Chevy Trucks

1967-72 Longbed to Shortbed Conversion Kit
Includes templates and c-channel supports
Available for C10 and C20 trucks
Welding is required Learn More

The 1947-54 Chevy Pickup Rear Dropmember suspension system is engineered to lay body with large diameter wheel/tire combinations. (Recommended to run no wider than a 10” wheel)

Ride Height - 4"
Deflated Height - Lay Body

The 1960-62 Chevy Pickup Rear Dropmember suspension system is engineered to lay body with large diameter wheel/tire combinations. (Recommended to run no wider than a 10” wheel)

Ride Height - 4"
Deflated Height - Lay Body"

The 1955-59 Chevy Pickup Rear Airbag Dropmember suspension system is engineered to lay body with large diameter wheel/tire combinations. (Recommended to run no wider than a 10” wheel)

Ride Height - 4"
Deflated Height - Lay Body"

The Porterbuilt 1960-62 Rear coilover suspension system is a modular suspension system designed to replace the factory components and improve ride quality, performance, aesthetics, and strength.

The 1955-59 Chevy Pickup Rear Coilover Dropmember suspension system is engineered to improve ride quality, performance, aesthetics, and strength.

Ride Height - 5-6"

The 1947-54 Chevy Pickup Rear Coilover Dropmember suspension system is engineered to improve ride quality, performance, aesthetics, and strength.

Ride Height - 5-6"

The 1973-87 Chevy Pickup Rear Level 2 Coilover Dropmember suspension system is engineered to improve ride quality, performance, aesthetics, and strength.

Ride Height - 7-9"

The 1973-87 Chevy Pickup Rear Level 2 Coilover Dropmember suspension system is engineered to improve ride quality, performance, aesthetics, and strength.

Ride Height - 4-6"

The Porterbuilt Bolt-on Body Drop for the 1967-1972 C10 is for those guys who just can’t be low enough! It is designed to make it easier to set the pinch weld level to the bottom of the frame.

The Dropmember Rear Back Half suspension system is engineered fit 12-15" wide wheels.
Fits 1963-72 C10 Trucks
Level 2, Touring
Ride height measures approx. 5” when running a 30” tall tire.

DESIGNED FOR 12"-15" WIDE WHEELS
LONG BED TO SHORT BED CONVERSION

The 1963-72 Chevy Pickup Rear Level 2 Coilover Dropmember suspension system is engineered to improve ride quality, performance, aesthetics, and strength.

Ride Height - 4-6"

The 1963-72 Chevy Pickup Rear Level 2 Coilover Dropmember suspension system is engineered to improve ride quality, performance, aesthetics, and strength.

Ride Height - 7-9"

The Dropmember Rear Back Half suspension system is engineered to lay frame with 12-15" wide wheels.
Fits 1963-72 C10 Trucks
Level 3, Extreme
Ride height measures approx. 5” and the frame will rest on the ground when deflated.

DESIGNED FOR 12"-15" WIDE WHEELS
LONG BED TO SHORT BED CONVERSION

The Dropmember Rear Back Half suspension system is engineered to lay frame with 12" wide wheels.
Fits 1960-62 C10 Trucks
Level 3, Extreme
Ride height measures approx. 5” when running a 30” tall tire, and the frame will rest on the ground when deflated.

DESIGNED FOR 12" WIDE WHEELS
LONG BED TO SHORT BED CONVERSION

Product Number: 14038
Approx 19 Gallons

1973-87 Chevy C10
Standard
Bed Fill
Non-EFI

* Pictures may show optional accessories installed. Depending upon the options you choose your tank may vary slightly from shown.

Product Number: 14039
Approx 19 Gallons

1973-87 Chevy C10
Standard
Side Fill
Non-EFI

* Pictures may show optional accessories installed. Depending upon the options you choose your tank may vary slightly from shown.

The 1963-72 Chevy Blazer 4WD Rear Level 3 Airbag Dropmember suspension system is engineered to lay frame with large diameter wheel/tire combinations.

Ride Height - 4"
Deflated Height - Lay Frame

The 1963-72 Chevy Blazer 2WD Rear Level 3 Airbag Dropmember suspension system is engineered to lay frame with large diameter wheel/tire combinations.

Ride Height - 4"
Deflated Height - Lay Frame

The 1973-87 Chevy Pickup Rear Level 3 Airbag Dropmember suspension system is engineered to lay frame with large diameter wheel/tire combinations.

Ride Height - 4"
Deflated Height - Lay Frame

The 1963-72 Chevy Pickup Rear Level 3 Airbag Dropmember suspension system is engineered to lay frame with large diameter wheel/tire combinations.

Ride Height - 4"
Deflated Height - Lay Frame

The 1947-54 Chevy Pickup Front Dropmember suspension system is a modular bolt-in sub-frame assembly engineered to incorporate Porterbuilt and C10 based suspension components.
When combined with a 2.5” drop spindle, 28” tall tire, and Porterbuilt Tubular Control Arms, the Level 2 Front will set the bottom of the cab approx. 5-6" inches off the ground at ride height.

Ride Height - 5-6"

The 1955-59 Chevy Pickup Front Dropmember suspension system is a modular bolt-in sub-frame assembly engineered to incorporate Porterbuilt and C10 based suspension components.
When combined with a 2.5” drop spindle, 28” tall tire, and Porterbuilt Tubular Control Arms, the Level 2 Front will set the bottom of the cab approx. 5-6" inches off the ground at ride height.

Ride Height - 5-6"

The Dropmember Rear Back Half suspension system is engineered fit 12" wide wheels.
Fits 1960-62 C10 Trucks
Level 2, Touring
Ride height measures approx. 5” when running a 30” tall tire.

DESIGNED FOR 12" WIDE WHEELS
LONG BED TO SHORT BED CONVERSION

Product Number: 14040
Approx 19 Gallons

1973-87 Chevy C10
Bed Fill
Aeromotive In-Tank Pump

Product Number: 14040
Approx 19 Gallons

1973-87 Chevy C10
Side Fill
Aeromotive In-Tank Pump

The 1960-62 Chevy Pickup Front Dropmember Coilover suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 2 Front Coilover system will set the lowest point of the factory frame rails approx. 5-6" inches off the ground at ride height.

Ride Height - 5-6"

THESE CONTROL ARMS ARE FOR VERSION 7, COILOVER DROPMEMBER APPLICATIONS ONLY.

Porterbuilt tubular control arms are built using thick-wall DOM tubing and CNC cut 3/16" pickeled plate steel. All bushing pivot tubes and ball joint cups are TIG welded.

Includes shafts, bushings, and Grade 8 hardware for installation.

NOTE: ALL CONTROL ARMS ARE DESIGNED TO USE PROFORGED BALL JOINTS. .

The 1955-59 Chevy Pickup Front Dropmember suspension system is a modular bolt-in sub-frame assembly engineered to incorporate Porterbuilt and C10 based suspension components.
When combined with a 2.5” drop spindle, 28” tall tire, and Porterbuilt Tubular Control Arms, the Level 3 Front will set the lowest point of the factory sheet metal on the ground when fully deflated.

Ride Height - 4"
Deflated Height - Lay Frame

The 1947-54 Chevy Pickup Front Dropmember suspension system is a modular bolt-in sub-frame assembly engineered to incorporate Porterbuilt and C10 based suspension components.
When combined with a 2.5” drop spindle, 28” tall tire, and Porterbuilt Tubular Control Arms, the Level 3 Front will set the lowest point of the factory sheet metal on the ground when fully deflated.

Ride Height - 4"
Deflated Height - Lay Frame

The Porterbuilt Stage 2 Rear “Deluxe” Kit for 63-72 C10 is an engineered bolt-in suspension system designed to lower your truck as low as possible while maintaining the factory bed floor. The Stage 2 “Deluxe” is just that, it replaces all the factory crossmembers (from the trailing arm cross-member back) with tubular versions that are designed to bolt right in! It also includes our fully adjustable trac bar for improved handling and performance. If you are looking for the best possible kit to lower your C10 and keep the bed-floor in tact… this is the one!

Product Number: 14003
Approx 19 Gallons

1963-72 Chevy C10
Side Fill
Aeromotive In-Tank Pump

Product Number: 14002
Approx 19 Gallons

1963-72 Chevy C10
Standard
Side Fill
Non-EFI

* Shown With Optional Rollover Vent and Sending Unit Installed.

The 1963-72 Chevy Pickup Rear Level 1 Airbag Dropmember suspension system is designed to replace the factory components and improve ride quality, performance, aesthetics, and strength.

Ride Height - 7"
Deflated Height - 3"

The 1973-87 Chevy Pickup Rear Level 1 Airbag Dropmember suspension system is designed to replace the factory components and improve ride quality, performance, aesthetics, and strength.

Ride Height - 7"
Deflated Height - 3"

The Dropmember Level 3 61-64 Ford F100 Front suspension system is a modular bolt-in sub-frame assembly engineered to incorporate Porterbuilt and C10 based suspension components.
When combined with a 2.5” drop spindle, 28” tall tire, and Porterbuilt Tubular Control Arms, the Level 3 Front will set the lowest point of the factory sheet metal on the ground when fully deflated.

The 1960-62 Chevy Pickup Front Dropmember suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 3 Front will set the lowest point of the factory frame rails on the ground when fully deflated.

Ride Height - 4"
Deflated Height - Lay Frame

Product Number: 14004
Approx 19 Gallons

1963-72 Chevy C10
Bed Fill
Aeromotive In-Tank Pump

The 1963-72 Chevy Pickup Front Dropmember suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 3 Front will set the lowest point of the factory frame rails on the ground when fully deflated.

Ride Height - 4"
Deflated Height - Lay Frame

The 1973-87 Chevy Pickup Front Dropmember suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 3 Front will set the lowest point of the factory frame rails on the ground when fully deflated.

Ride Height - 4"
Deflated Height - Lay Frame

Product Number: 14001
Approx 19 Gallons

1963-72 Chevy C10
Standard
Bed Fill
Non-EFI

* Shown With Optional Rollover Vent and Sending Unit Installed.

Boxed carrier bearing crossmember built using 3/16" steel.

Fits: 1973-87 Chevy Trucks

Tubular carrier bearing crossmember built using thick-wall 1.5" tubing & 3/16" steel.

Fits: 1963-72 Chevy Trucks

The 1963-72 Chevy Pickup Front Dropmember suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 1 Front will the lowest point of the factory frame rails approx. 3” off the ground when fully deflated.

Ride Height - 6-7"
Deflated Height - 3"

The 1973-87 Chevy Pickup Front Dropmember suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 1 Front will the lowest point of the factory frame rails approx. 3” off the ground when fully deflated.

Ride Height - 6-7"
Deflated Height - 3"

Tubular trailing arm crossmember built using thick-wall 1.5" tubing & 3/16" steel.

Fits: 1963-72 Chevy Trucks

Tubular trailing arm crossmember built using thick-wall 1.5" tubing & 3/16" steel.

Fits: 1963-72 Chevy Trucks

Tubular trailing arm crossmember built using thick-wall 1.5" tubing & 3/16" steel.

Fits: 1963-72 Chevy Trucks

The 1963-72 Chevy Pickup Front Dropmember Coilover suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 2 Front will set the bottom of the cab approx. 4-6" inches off the ground at ride height.

Ride Height - 4-6"

The 1963-72 Chevy Pickup Front Dropmember Coilover suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 1 Front will set the bottom of the cab approx. 7-9" inches off the ground at ride height.

Ride Height - 7-9"

The 1973-87 Chevy Pickup Front Dropmember Coilover suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 1 Front will set the bottom of the cab approx. 7-9" inches off the ground at ride height.

Ride Height - 7-9"

The 1973-87 Chevy Pickup Front Dropmember Coilover suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 2 Front will set the bottom of the cab approx. 4-6" inches off the ground at ride height.

Ride Height - 4-6"

The Porterbuilt cowl mounted hood hinges are the perfect solution to relocating the hood hinges once the factory inner fender wells have been removed. They are available for model years 1960-1972 and start at $299 for the non-gas assist, or $399 with gas assist (this option is currently only available for the 67-72 trucks).

The non-gas assist version can later be upgraded to gas assist for $189.

The Porterbuilt cowl mounted hood hinges are the perfect solution to relocating the hood hinges once the factory inner fender wells have been removed. They are available for model years 1960-1972 and start at $299 for the non-gas assist, or $399 with gas assist (this option is currently only available for the 67-72 trucks).

The non-gas assist version can later be upgraded to gas assist for $189.

If you are looking for the best possible kit to convert your truck to air suspension but maintain your factory front crossmember, this is the kit for you. The Porterbuilt Stage 2 Deluxe Front Kit for '63-'87 Chevy Trucks replaces your factory control arms and coil springs, lowering your truck and improving handling, without replacing the factory front crossmember.