The 1955-59 Chevy Pickup Front Dropmember suspension system is a modular bolt-in sub-frame assembly engineered to incorporate Porterbuilt and C10 based suspension components.
When combined with a 2.5” drop spindle, 28” tall tire, and Porterbuilt Tubular Control Arms, the Level 3 Front will set the lowest point of the factory sheet metal on the ground when fully deflated.
The 1947-54 Chevy Pickup Front Dropmember suspension system is a modular bolt-in sub-frame assembly engineered to incorporate Porterbuilt and C10 based suspension components.
When combined with a 2.5” drop spindle, 28” tall tire, and Porterbuilt Tubular Control Arms, the Level 3 Front will set the lowest point of the factory sheet metal on the ground when fully deflated.
The 1960-62 Chevy Pickup Front Dropmember suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 3 Front will set the lowest point of the factory frame rails on the ground when fully deflated.
The 1963-72 Chevy Pickup Front Dropmember suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 3 Front will set the lowest point of the factory frame rails on the ground when fully deflated.
The 1960-62 Chevy Pickup Front Dropmember Coilover suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 2 Front Coilover system will set the lowest point of the factory frame rails approx. 5-6" inches off the ground at ride height.
The 1963-72 Chevy Pickup Front Dropmember suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 1 Front will the lowest point of the factory frame rails approx. 3” off the ground when fully deflated.
The 1973-87 Chevy Pickup Front Dropmember suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 1 Front will the lowest point of the factory frame rails approx. 3” off the ground when fully deflated.
Wilwood Forged Narrow Superlite 6R Front Brake Kit
13.06" Rotors, Drilled & Slotted Available
6 Piston Calipers, Red or Black Available
17" Minimum Wheel Diameter
* FOR USE WITH CPP MODULAR SPINDLES
Learn MoreWilwood Forged Narrow Superlite 6R Front Brake Kit
12.19" Rotors, SRP Drilled & Slotted Available
6 Piston Calipers, Red or Black Available
15" Minimum Wheel Diameter
* FOR USE WITH WILWOOD C10 PRO SPINDLES
Learn MoreWilwood Forged Narrow Superlite 6R Front Brake Kit
14" Rotors, SRP Drilled & Slotted Available
6 Piston Calipers, Red or Black Available
18" Minimum Wheel Diameter
* FOR USE WITH WILWOOD C10 PRO SPINDLES
Learn MoreWilwood Forged Narrow Superlite 6R Front Brake Kit
13.06" Rotors, SRP Drilled & Slotted Available
6 Piston Calipers, Red or Black Available
17" Minimum Wheel Diameter
* FOR USE WITH WILWOOD C10 PRO SPINDLES
Learn MoreWilwood Forged Narrow Superlite 6R Front Brake Kit
14" Rotors, SRP Drilled & Slotted Available
6 Piston Calipers, Red or Black Available
18" Minimum Wheel Diameter
* FOR USE WITH WILWOOD C10 STEEL SPINDLES
Learn MoreWilwood Forged Narrow Superlite 6R Front Brake Kit
13" Rotors, SRP Drilled & Slotted Available
6 Piston Calipers, Red or Black Available
17" Minimum Wheel Diameter
* FOR USE WITH WILWOOD C10 STEEL SPINDLES
Learn MoreWilwood Forged Narrow Superlite 6R Front Brake Kit
12" 1 Piece Rotor and Hats, SRP Drilled & Slotted Available
6 Piston Calipers, Red or Black Available
15" Minimum Wheel Diameter
* FOR USE WITH WILWOOD C10 STEEL SPINDLES
Learn MoreTubular transmission crossmember built using thick-wall 1.5" tubing & 3/16" steel.
Tubular transmission crossmember built using thick-wall 1.5" tubing & 3/16" steel.
Wilwood Forged Narrow Superlite 6R Front Brake Kit
6 Lug
14" Rotors, Drilled & Slotted Available
6 Piston Calipers, Red or Black Available
18" Minimum Wheel Diameter
* FOR USE WITH CPP MODULAR SPINDLES
Learn MoreWilwood Forged Narrow Superlite 6R Front Brake Kit
6 Lug
13.06" Rotors, Drilled & Slotted Available
6 Piston Calipers, Red or Black Available
17" Minimum Wheel Diameter
* FOR USE WITH CPP MODULAR SPINDLES
Learn MoreWilwood Forged Narrow Superlite 6R Front Brake Kit
6 Lug
13" Rotors, SRP Drilled & Slotted Available
6 Piston Calipers, Red or Black Available
17" Minimum Wheel Diameter
* FOR USE WITH WILWOOD C10 STEEL SPINDLES
Learn MoreTubular core support crossmember built using thick-wall 1.5" tubing & 3/16" steel.
Tubular core support crossmember built using thick-wall 1.5" tubing & 3/16" steel.
Tubular core support crossmember built using thick-wall 1.5" tubing & 3/16" steel.
Wilwood Forged Narrow Superlite 6R Front Brake Kit
6 Lug
12" 1 Piece Rotor and Hats, SRP Drilled & Slotted Available
6 Piston Calipers, Red or Black Available
15" Minimum Wheel Diameter
* FOR USE WITH WILWOOD C10 STEEL SPINDLES
Learn MoreWilwood Forged Narrow Superlite 6R Front Brake Kit
6 Lug
14" Rotors, SRP Drilled & Slotted Available
6 Piston Calipers, Red or Black Available
18" Minimum Wheel Diameter
* FOR USE WITH WILWOOD C10 STEEL SPINDLES
Learn MoreThe 1947-54 Chevy Pickup Front Dropmember suspension system is a modular bolt-in sub-frame assembly engineered to incorporate Porterbuilt and C10 based suspension components.
When combined with a 2.5” drop spindle, 28” tall tire, and Porterbuilt Tubular Control Arms, the Level 2 Front will set the bottom of the cab approx. 5-6" inches off the ground at ride height.
The 1955-59 Chevy Pickup Front Dropmember suspension system is a modular bolt-in sub-frame assembly engineered to incorporate Porterbuilt and C10 based suspension components.
When combined with a 2.5” drop spindle, 28” tall tire, and Porterbuilt Tubular Control Arms, the Level 2 Front will set the bottom of the cab approx. 5-6" inches off the ground at ride height.
The 1963-72 Chevy Pickup Front Dropmember Coilover suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 2 Front will set the bottom of the cab approx. 4-6" inches off the ground at ride height.
The 1963-72 Chevy Pickup Front Dropmember Coilover suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 1 Front will set the bottom of the cab approx. 7-9" inches off the ground at ride height.
The 1973-87 Chevy Pickup Front Dropmember Coilover suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 1 Front will set the bottom of the cab approx. 7-9" inches off the ground at ride height.
The 1973-87 Chevy Pickup Front Dropmember Coilover suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 2 Front will set the bottom of the cab approx. 4-6" inches off the ground at ride height.
The 1947-54 Chevy Pickup Rear Dropmember suspension system is engineered to lay body with large diameter wheel/tire combinations. (Recommended to run no wider than a 10” wheel)
The 1960-62 Chevy Pickup Rear Dropmember suspension system is engineered to lay body with large diameter wheel/tire combinations. (Recommended to run no wider than a 10” wheel)
Tubular transmission crossmember built using thick-wall 1.5" tubing & 3/16" steel.
Tubular transmission crossmember built using thick-wall 1.5" tubing & 3/16" steel.
Note: The tabs are loose and "unwelded".
Tubular core support crossmember built using thick-wall 1.5" tubing & 3/16" steel.
Tubular core support crossmember built using thick-wall 1.5" tubing & 3/16" steel.
The 1963-72 Chevy Pickup Rear Level 2 Coilover Dropmember suspension system is engineered to improve ride quality, performance, aesthetics, and strength.
The 1963-72 Chevy Pickup Rear Level 2 Coilover Dropmember suspension system is engineered to improve ride quality, performance, aesthetics, and strength.
The 1973-87 Chevy Pickup Rear Level 3 Airbag Dropmember suspension system is engineered to lay frame with large diameter wheel/tire combinations.
The 1963-72 Chevy Pickup Rear Level 3 Airbag Dropmember suspension system is engineered to lay frame with large diameter wheel/tire combinations.
The 1963-72 Chevy Pickup Rear Level 1 Airbag Dropmember suspension system is designed to replace the factory components and improve ride quality, performance, aesthetics, and strength.
The 1973-87 Chevy Pickup Rear Level 1 Airbag Dropmember suspension system is designed to replace the factory components and improve ride quality, performance, aesthetics, and strength.
The 1963-72 Chevy Blazer 2WD Rear Level 3 Airbag Dropmember suspension system is engineered to lay frame with large diameter wheel/tire combinations.
The 1963-72 Chevy Blazer 4WD Rear Level 3 Airbag Dropmember suspension system is engineered to lay frame with large diameter wheel/tire combinations.
The 1955-59 Chevy Pickup Rear Coilover Dropmember suspension system is engineered to improve ride quality, performance, aesthetics, and strength.
The 1947-54 Chevy Pickup Rear Coilover Dropmember suspension system is engineered to improve ride quality, performance, aesthetics, and strength.
The 1973-87 Chevy Pickup Rear Level 2 Coilover Dropmember suspension system is engineered to improve ride quality, performance, aesthetics, and strength.
The 1973-87 Chevy Pickup Rear Level 2 Coilover Dropmember suspension system is engineered to improve ride quality, performance, aesthetics, and strength.
The Porterbuilt 1960-62 Rear coilover suspension system is a modular suspension system designed to replace the factory components and improve ride quality, performance, aesthetics, and strength.
Ride height measures approx. 6” when running a 30” tall tire (measurements are taken from bottom of the cab to the ground).16" Big Brake Kit From Little Shop Manufacturing
Available with Wilwood 6 Piston Calipers or MFG 6 Piston Calipers
Comes with Drilled & Slotted Rotors
FITS WILWOOD ALUMINUM PROSPINDLE ONLY (NOT INCLUDED)
Learn MoreWilwood Forged Narrow Superlite 6R Front Brake Kit
14" Rotors, Drilled & Slotted Available
6 Piston Calipers, Red or Black Available
18" Minimum Wheel Diameter
* FOR USE WITH CPP MODULAR SPINDLES
Learn MoreThe Dropmember Rear Back Half suspension system is engineered fit 12-15" wide wheels.
Fits 1963-72 C10 Trucks
Level 2, Touring
Ride height measures approx. 5” when running a 30” tall tire.
The Dropmember Rear Back Half suspension system is engineered fit 12" wide wheels.
Fits 1960-62 C10 Trucks
Level 2, Touring
Ride height measures approx. 5” when running a 30” tall tire.
The Dropmember Rear Back Half suspension system is engineered to lay frame with 12" wide wheels.
Fits 1960-62 C10 Trucks
Level 3, Extreme
Ride height measures approx. 5” when running a 30” tall tire, and the frame will rest on the ground when deflated.
The Dropmember Rear Back Half suspension system is engineered to lay frame with 12-15" wide wheels.
Fits 1963-72 C10 Trucks
Level 3, Extreme
Ride height measures approx. 5” and the frame will rest on the ground when deflated.
Tubular trailing arm crossmember built using thick-wall 1.5" tubing & 3/16" steel.
Tubular trailing arm crossmember built using thick-wall 1.5" tubing & 3/16" steel.
Tubular trailing arm crossmember built using thick-wall 1.5" tubing & 3/16" steel.
Tubular carrier bearing crossmember built using thick-wall 1.5" tubing & 3/16" steel.
Tubular rear frame crossmember built using thick-wall 1.5" tubing & 3/16" steel.
Tubular rear frame crossmember built using thick-wall 1.5" tubing & 3/16" steel.
Tubular rear frame crossmember built using thick-wall 1.5" tubing & 3/16" steel.
Boxed Trailing Arm Crossmember built using 3/16" steel for a 2-piece driveshaft configuration.
Tubular rear frame crossmember built using thick-wall 1.5" tubing & 3/16" steel.
Product Number: 14040
Approx 19 Gallons
1973-87 Chevy C10
Side Fill
Aeromotive In-Tank Pump
Product Number: 14003
Approx 19 Gallons
1963-72 Chevy C10
Side Fill
Aeromotive In-Tank Pump
Product Number: 14038
Approx 19 Gallons
1973-87 Chevy C10
Standard
Bed Fill
Non-EFI
* Pictures may show optional accessories installed. Depending upon the options you choose your tank may vary slightly from shown.
Learn MoreProduct Number: 14039
Approx 19 Gallons
1973-87 Chevy C10
Standard
Side Fill
Non-EFI
* Pictures may show optional accessories installed. Depending upon the options you choose your tank may vary slightly from shown.
Learn MoreProduct Number: 14002
Approx 19 Gallons
1963-72 Chevy C10
Standard
Side Fill
Non-EFI
* Shown With Optional Rollover Vent and Sending Unit Installed.
Learn MoreProduct Number: 14001
Approx 19 Gallons
1963-72 Chevy C10
Standard
Bed Fill
Non-EFI
* Shown With Optional Rollover Vent and Sending Unit Installed.
Learn MoreTubular panhard bar crossmember built using thick-wall 1.5" tubing & 3/16" steel.