Search results for: 'c notch 87 c10'

The 1963-72 Chevy Pickup Rear Level 1 Airbag Dropmember suspension system is designed to replace the factory components and improve ride quality, performance, aesthetics, and strength.

Ride Height - 7"
Deflated Height - 3"

The Dropmember Level 3 61-64 Ford F100 Front suspension system is a modular bolt-in sub-frame assembly engineered to incorporate Porterbuilt and C10 based suspension components.
When combined with a 2.5” drop spindle, 28” tall tire, and Porterbuilt Tubular Control Arms, the Level 3 Front will set the lowest point of the factory sheet metal on the ground when fully deflated.

These stainless steel headers are used with the Porterbuilt Level 3 Dropmember (Version 5, 6 & 7) when doing an LS swap.

The 1963-72 Chevy Blazer 2WD Rear Level 3 Airbag Dropmember suspension system is engineered to lay frame with large diameter wheel/tire combinations.

Ride Height - 4"
Deflated Height - Lay Frame

The 1963-72 Chevy Blazer 4WD Rear Level 3 Airbag Dropmember suspension system is engineered to lay frame with large diameter wheel/tire combinations.

Ride Height - 4"
Deflated Height - Lay Frame

The Porterbuilt Bolt-on Body Drop for the 1967-1972 C10 is for those guys who just can’t be low enough! It is designed to make it easier to set the pinch weld level to the bottom of the frame.

If you are thinking about lowering your C10 truck more than four inches in the rear, a longer trac-bar will be a necessity! The Porterbuilt Fully Adjustable Trac-bar has an overall length of just over 34 inches. The longer the bar, the less side to side shift the differential will experience through suspension travel. The new mounting brackets also relocate the bar lowering the rear roll-center, and the bar length can be tuned while still mounted on the truck!

The 1963-72 Chevy Pickup Front Dropmember Coilover suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 2 Front will set the bottom of the cab approx. 4-6" inches off the ground at ride height.

Ride Height - 4-6"

The 1963-72 Chevy Pickup Front Dropmember Coilover suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 1 Front will set the bottom of the cab approx. 7-9" inches off the ground at ride height.

Ride Height - 7-9"

Tubular core support crossmember built using thick-wall 1.5" tubing & 3/16" steel.

Fits: 1947-54 Chevy Trucks

Tubular core support crossmember built using thick-wall 1.5" tubing & 3/16" steel.

Fits: 1963-66 Chevy Trucks

Tubular core support crossmember built using thick-wall 1.5" tubing & 3/16" steel.

Fits: 1967-72 Chevy Trucks

Wilwood Forged Narrow Superlite 6R Front Brake Kit
14" Rotors, Drilled & Slotted Available
6 Piston Calipers, Red or Black Available
18" Minimum Wheel Diameter

* FOR USE WITH CPP MODULAR SPINDLES

Wilwood Forged Narrow Superlite 6R Front Brake Kit
13.06" Rotors, Drilled & Slotted Available
6 Piston Calipers, Red or Black Available
17" Minimum Wheel Diameter

* FOR USE WITH CPP MODULAR SPINDLES

Wilwood Forged Narrow Superlite 6R Front Brake Kit
6 Lug
14" Rotors, Drilled & Slotted Available
6 Piston Calipers, Red or Black Available
18" Minimum Wheel Diameter

* FOR USE WITH CPP MODULAR SPINDLES

Wilwood Forged Narrow Superlite 6R Front Brake Kit
6 Lug
13.06" Rotors, Drilled & Slotted Available
6 Piston Calipers, Red or Black Available
17" Minimum Wheel Diameter

* FOR USE WITH CPP MODULAR SPINDLES

The 1960-62 Chevy Pickup Front Dropmember Coilover suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 2 Front Coilover system will set the lowest point of the factory frame rails approx. 5-6" inches off the ground at ride height.

Ride Height - 5-6"

The 1955-59 Chevy Pickup Front Dropmember suspension system is a modular bolt-in sub-frame assembly engineered to incorporate Porterbuilt and C10 based suspension components.
When combined with a 2.5” drop spindle, 28” tall tire, and Porterbuilt Tubular Control Arms, the Level 3 Front will set the lowest point of the factory sheet metal on the ground when fully deflated.

Ride Height - 4"
Deflated Height - Lay Frame

The 1947-54 Chevy Pickup Front Dropmember suspension system is a modular bolt-in sub-frame assembly engineered to incorporate Porterbuilt and C10 based suspension components.
When combined with a 2.5” drop spindle, 28” tall tire, and Porterbuilt Tubular Control Arms, the Level 3 Front will set the lowest point of the factory sheet metal on the ground when fully deflated.

Ride Height - 4"
Deflated Height - Lay Frame

The stage 1 rear kit is both an economical and easy way to lower the rear of your 63-72 C10′s trailing arm suspension. The air spring and mounting plates replace the factory steel coil spring, allowing a better ride quality and adjustability! Our Stage 1 shock relocator brackets improve shock function by decreasing the shock angle!

The Porterbuilt cowl mounted hood hinges are the perfect solution to relocating the hood hinges once the factory inner fender wells have been removed. They are available for model years 1960-1972.

Tubular panhard bar crossmember built using thick-wall 1.5" tubing & 3/16" steel.

Fits: 1963-72 Chevy Trucks

Tubular carrier bearing crossmember built using thick-wall 1.5" tubing & 3/16" steel.

Fits: 1963-72 Chevy Trucks

Boxed Trailing Arm Crossmember built using 3/16" steel for a 2-piece driveshaft configuration.

Fits: 1955-59 Chevy Trucks

Tubular rear frame crossmember built using thick-wall 1.5" tubing & 3/16" steel.

Fits: 1955-59 Chevy Trucks

Tubular rear frame crossmember built using thick-wall 1.5" tubing & 3/16" steel.

Fits: 1960-62 Chevy Trucks

Tubular trailing arm crossmember built using thick-wall 1.5" tubing & 3/16" steel.

Fits: 1963-72 Chevy Trucks

Tubular trailing arm crossmember built using thick-wall 1.5" tubing & 3/16" steel.

Fits: 1963-72 Chevy Trucks

Tubular rear frame crossmember built using thick-wall 1.5" tubing & 3/16" steel.

Fits: 1963-72 Chevy Trucks

New boxed rear frame crossmember fabricated from 3/16" steel.

Fits: 1963-72 Chevy Trucks

Tubular core support crossmember built using thick-wall 1.5" tubing & 3/16" steel.

Fits: 1955-59 Chevy Trucks

Tubular transmission crossmember built using thick-wall 1.5" tubing & 3/16" steel.

Fits: 1955-59 Chevy Trucks

Tubular trailing arm crossmember built using thick-wall 1.5" tubing & 3/16" steel.

Fits: 1963-72 Chevy Trucks

Tubular transmission crossmember built using thick-wall 1.5" tubing & 3/16" steel.

Fits: 1947-54 Chevy Trucks

Tubular transmission crossmember built using thick-wall 1.5" tubing & 3/16" steel.

Note: The tabs are loose and "unwelded".

Fits: 1960-62 Chevy Trucks

Boxed trailing arm crossmember built using 3/16" steel.

Fits: 1963-72 Chevy Trucks

Boxed trailing arm crossmember built using 3/16" steel.

Fits: 1963-72 Chevy Trucks

THESE CONTROL ARMS ARE FOR VERSION 7 DROPMEMBER APPLICATIONS ONLY.

Porterbuilt tubular control arms are built using thick-wall DOM tubing and CNC cut 3/16" pickeled plate steel. All bushing pivot tubes and ball joint cups are TIG welded.

Includes shafts, bushings, and Grade 8 hardware for installation.

NOTE: ALL CONTROL ARMS ARE DESIGNED TO USE PROFORGED BALL JOINTS. .

THESE CONTROL ARMS ARE FOR EARLY (PRE VERSION 7) DROPMEMBER APPLICATIONS ONLY.

Porterbuilt tubular control arms are built using thick-wall DOM tubing and CNC cut 3/16" pickeled plate steel. All bushing pivot tubes and ball joint cups are TIG welded.

Includes shafts, bushings, and Grade 8 hardware for installation.

NOTE: ALL CONTROL ARMS ARE DESIGNED TO USE PROFORGED BALL JOINTS. .

The 1960-62 Chevy Pickup Front Dropmember suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 3 Front will set the lowest point of the factory frame rails on the ground when fully deflated.

Ride Height - 4"
Deflated Height - Lay Frame

The 1963-72 Chevy Pickup Front Dropmember suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 3 Front will set the lowest point of the factory frame rails on the ground when fully deflated.

Ride Height - 4"
Deflated Height - Lay Frame

The 1963-72 Chevy Pickup Front Dropmember suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 1 Front will the lowest point of the factory frame rails approx. 3” off the ground when fully deflated.

Ride Height - 6-7"
Deflated Height - 3"

The Porterbuilt Stage 2 Rear “Deluxe” Kit for 63-72 C10 is an engineered bolt-in suspension system designed to lower your truck as low as possible while maintaining the factory bed floor. The Stage 2 “Deluxe” is just that, it replaces all the factory crossmembers (from the trailing arm cross-member back) with tubular versions that are designed to bolt right in! It also includes our fully adjustable trac bar for improved handling and performance. If you are looking for the best possible kit to lower your C10 and keep the bed-floor in tact… this is the one!