The 1973-87 Chevy Pickup Rear Level 2 Coilover Dropmember suspension system is engineered to improve ride quality, performance, aesthetics, and strength.
The 1973-87 Chevy Pickup Front Dropmember Coilover suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 1 Front will set the bottom of the cab approx. 7-9" inches off the ground at ride height.
The 1963-72 Chevy Pickup Front Dropmember Coilover suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 1 Front will set the bottom of the cab approx. 7-9" inches off the ground at ride height.
The 1963-72 Chevy Pickup Rear Level 2 Coilover Dropmember suspension system is engineered to improve ride quality, performance, aesthetics, and strength.
The 1973-87 Chevy Pickup Rear Level 2 Coilover Dropmember suspension system is engineered to improve ride quality, performance, aesthetics, and strength.
The 1963-72 Chevy Pickup Rear Level 2 Coilover Dropmember suspension system is engineered to improve ride quality, performance, aesthetics, and strength.
The 1973-87 Chevy Pickup Front Dropmember Coilover suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 2 Front will set the bottom of the cab approx. 4-6" inches off the ground at ride height.
The 1963-72 Chevy Pickup Front Dropmember Coilover suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 2 Front will set the bottom of the cab approx. 4-6" inches off the ground at ride height.
The Dropmember Rear Back Half suspension system is engineered fit 12-15" wide wheels.
Fits 1963-72 C10 Trucks
Level 2, Touring
Ride height measures approx. 5” when running a 30” tall tire.
The Dropmember Rear Back Half suspension system is engineered fit 12" wide wheels.
Fits 1960-62 C10 Trucks
Level 2, Touring
Ride height measures approx. 5” when running a 30” tall tire.
The 1963-72 Chevy Pickup Rear Level 1 Airbag Dropmember suspension system is designed to replace the factory components and improve ride quality, performance, aesthetics, and strength.
The 1973-87 Chevy Pickup Rear Level 1 Airbag Dropmember suspension system is designed to replace the factory components and improve ride quality, performance, aesthetics, and strength.
The 1955-59 Chevy Pickup Rear Coilover Dropmember suspension system is engineered to improve ride quality, performance, aesthetics, and strength.
The 1947-54 Chevy Pickup Rear Coilover Dropmember suspension system is engineered to improve ride quality, performance, aesthetics, and strength.
The 1963-72 Chevy Pickup Front Dropmember suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 1 Front will the lowest point of the factory frame rails approx. 3” off the ground when fully deflated.
The 1973-87 Chevy Pickup Front Dropmember suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 1 Front will the lowest point of the factory frame rails approx. 3” off the ground when fully deflated.
The 1960-62 Chevy Pickup Front Dropmember Coilover suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 2 Front Coilover system will set the lowest point of the factory frame rails approx. 5-6" inches off the ground at ride height.
The Porterbuilt 1960-62 Rear coilover suspension system is a modular suspension system designed to replace the factory components and improve ride quality, performance, aesthetics, and strength.
Ride height measures approx. 6” when running a 30” tall tire (measurements are taken from bottom of the cab to the ground).Replacement Shock Kit
Applications:
Dropmember Level 1, Dropmember Level 2, Dropmember Level 3
Stage 1 Front, Stage 2 Front
Stage 1 Rear, Stage 2 Rear Basic, Stage 2 Rear Deluxe
The 1947-54 Chevy Pickup Front Dropmember suspension system is a modular bolt-in sub-frame assembly engineered to incorporate Porterbuilt and C10 based suspension components.
When combined with a 2.5” drop spindle, 28” tall tire, and Porterbuilt Tubular Control Arms, the Level 2 Front will set the bottom of the cab approx. 5-6" inches off the ground at ride height.
The 1955-59 Chevy Pickup Front Dropmember suspension system is a modular bolt-in sub-frame assembly engineered to incorporate Porterbuilt and C10 based suspension components.
When combined with a 2.5” drop spindle, 28” tall tire, and Porterbuilt Tubular Control Arms, the Level 2 Front will set the bottom of the cab approx. 5-6" inches off the ground at ride height.
THESE CONTROL ARMS ARE FOR VERSION 7, COILOVER DROPMEMBER APPLICATIONS ONLY.
Porterbuilt tubular control arms are built using thick-wall DOM tubing and CNC cut 3/16" pickeled plate steel. All bushing pivot tubes and ball joint cups are TIG welded.
Includes shafts, bushings, and Grade 8 hardware for installation.
NOTE: ALL CONTROL ARMS ARE DESIGNED TO USE PROFORGED BALL JOINTS. .
Learn MoreThe 1973-87 Chevy Pickup Rear Level 3 Airbag Dropmember suspension system is engineered to lay frame with large diameter wheel/tire combinations.
The 1963-72 Chevy Pickup Rear Level 3 Airbag Dropmember suspension system is engineered to lay frame with large diameter wheel/tire combinations.
The 1963-72 Chevy Blazer 2WD Rear Level 3 Airbag Dropmember suspension system is engineered to lay frame with large diameter wheel/tire combinations.
The 1963-72 Chevy Blazer 4WD Rear Level 3 Airbag Dropmember suspension system is engineered to lay frame with large diameter wheel/tire combinations.
New Boxed Inner Frame Stiffener for Level 1 Dropmember, Static & Stock Suspension Trucks
The Dropmember Rear Back Half suspension system is engineered to lay frame with 12-15" wide wheels.
Fits 1963-72 C10 Trucks
Level 3, Extreme
Ride height measures approx. 5” and the frame will rest on the ground when deflated.
The Dropmember Rear Back Half suspension system is engineered to lay frame with 12" wide wheels.
Fits 1960-62 C10 Trucks
Level 3, Extreme
Ride height measures approx. 5” when running a 30” tall tire, and the frame will rest on the ground when deflated.
The stage 1 rear kit is both an economical and easy way to lower the rear of your 63-72 C10′s trailing arm suspension. The air spring and mounting plates replace the factory steel coil spring, allowing a better ride quality and adjustability! Our Stage 1 shock relocator brackets improve shock function by decreasing the shock angle!
Learn MoreThe 1973-87 Chevy Pickup Front Dropmember suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 3 Front will set the lowest point of the factory frame rails on the ground when fully deflated.
The Porterbuilt Stage 2 Rear “Deluxe” Kit for 63-72 C10 is an engineered bolt-in suspension system designed to lower your truck as low as possible while maintaining the factory bed floor. The Stage 2 “Deluxe” is just that, it replaces all the factory crossmembers (from the trailing arm cross-member back) with tubular versions that are designed to bolt right in! It also includes our fully adjustable trac bar for improved handling and performance. If you are looking for the best possible kit to lower your C10 and keep the bed-floor in tact… this is the one!
Learn MoreThe 1963-72 Chevy Pickup Front Dropmember suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 3 Front will set the lowest point of the factory frame rails on the ground when fully deflated.
THESE CONTROL ARMS ARE FOR VERSION 7 DROPMEMBER APPLICATIONS ONLY.
Porterbuilt tubular control arms are built using thick-wall DOM tubing and CNC cut 3/16" pickeled plate steel. All bushing pivot tubes and ball joint cups are TIG welded.
Includes shafts, bushings, and Grade 8 hardware for installation.
NOTE: ALL CONTROL ARMS ARE DESIGNED TO USE PROFORGED BALL JOINTS. .
Learn MoreLooking for an easy way to switch over to air suspension without breaking the bank? The Stage 1 front kit is an inexpensive and simple way to do just that! The Stage 1 front kit is designed to replace the factory steel coil spring with an air spring while maintaining the factory control arms.
NOTE: ALL CONTROL ARMS ARE DESIGNED TO USE PROFORGED BALL JOINTS. .
Learn MoreThe 1947-54 Chevy Pickup Rear Dropmember suspension system is engineered to lay body with large diameter wheel/tire combinations. (Recommended to run no wider than a 10” wheel)
The 1960-62 Chevy Pickup Rear Dropmember suspension system is engineered to lay body with large diameter wheel/tire combinations. (Recommended to run no wider than a 10” wheel)
The 1955-59 Chevy Pickup Rear Airbag Dropmember suspension system is engineered to lay body with large diameter wheel/tire combinations. (Recommended to run no wider than a 10” wheel)
THESE CONTROL ARMS ARE FOR EARLY (PRE VERSION 7) DROPMEMBER APPLICATIONS ONLY.
Porterbuilt tubular control arms are built using thick-wall DOM tubing and CNC cut 3/16" pickeled plate steel. All bushing pivot tubes and ball joint cups are TIG welded.
Includes shafts, bushings, and Grade 8 hardware for installation.
NOTE: ALL CONTROL ARMS ARE DESIGNED TO USE PROFORGED BALL JOINTS. .
Learn MoreThe Dropmember Level 3 61-64 Ford F100 Front suspension system is a modular bolt-in sub-frame assembly engineered to incorporate Porterbuilt and C10 based suspension components.
When combined with a 2.5” drop spindle, 28” tall tire, and Porterbuilt Tubular Control Arms, the Level 3 Front will set the lowest point of the factory sheet metal on the ground when fully deflated.
These stainless steel headers are used with the Porterbuilt Level 3 Dropmember (Version 5, 6 & 7) when doing an LS swap.
Learn MoreTubular trailing arm crossmember built using thick-wall 1.5" tubing & 3/16" steel.
The 1960-62 Chevy Pickup Front Dropmember suspension system is designed to replace the factory cross-member and steering system. It is engineered as a modular bolt-in unit that requires no welding.
When combined with a 2.5” drop spindle, 29” tall tire, and Porterbuilt Tubular Control Arms, the Level 3 Front will set the lowest point of the factory frame rails on the ground when fully deflated.
The 1955-59 Chevy Pickup Front Dropmember suspension system is a modular bolt-in sub-frame assembly engineered to incorporate Porterbuilt and C10 based suspension components.
When combined with a 2.5” drop spindle, 28” tall tire, and Porterbuilt Tubular Control Arms, the Level 3 Front will set the lowest point of the factory sheet metal on the ground when fully deflated.
The 1947-54 Chevy Pickup Front Dropmember suspension system is a modular bolt-in sub-frame assembly engineered to incorporate Porterbuilt and C10 based suspension components.
When combined with a 2.5” drop spindle, 28” tall tire, and Porterbuilt Tubular Control Arms, the Level 3 Front will set the lowest point of the factory sheet metal on the ground when fully deflated.
Air Lift Performance 3H combines pressure-based control with ride-height sensing technology. While both types of air management have been utilized before, this is the first product to harness the benefits of both sytems – instantly improving suspension control, performance, and vehicle ride flexibility.
NOTE: As of April 2024, all 3H and 3P manifolds come with 1/4" threaded FNPT ports.
Learn MoreThis standard Firestone air spring offers maximum load support and operates at up to 100 psi. The spring has a 1/4" inflation port, a ride height of 8.25" and a maximum diameter of 5.70".
* Includes 2 air springs
Learn MoreAir Lift Performance 3P combines pressure-based control with the ability to add ride-height sensing technology with the upgrade to height sensors. While both types of air management have been utilized before, this is the first product to harness the benefits of both sytems – instantly improving suspension control, performance, and vehicle ride flexibility.
NOTE: As of April 2024, all 3H and 3P manifolds come with 1/4" threaded FNPT ports.
Learn MoreBoxed Trailing Arm Crossmember built using 3/16" steel for a 2-piece driveshaft configuration.
New Boxed Inner Frame Stiffener for Level 2 & Level 3 Dropmember Equipped Trucks
New Inner Frame Stiffener for Level 2 & Level 3 Dropmember Equipped Trucks
New Boxed Inner Frame Stiffener for Level 2 & Level 3 Dropmember Equipped Trucks
New Boxed Inner Frame Stiffener for Level 2 & Level 3 Dropmember Equipped Trucks
New Boxed Inner Frame Stiffener for Level 2 & Level 3 Dropmember Equipped Trucks
Air Lift Performance is proud to announce the second model from the brand new Dominator series line of air springs: the Dominator D2600!
*Includes 2 air bags
Learn MorePorterbuilt tubular control arms are built using thick-wall DOM tubing and CNC cut 3/16" pickeled plate steel. All bushing pivot tubes and ball joint cups are TIG welded.
Available in the following configurations:
1" Forward
1" Narrowed
1" Forward & 1" Narrowed
Standard Length
Includes upper and lower shafts, bushings, and Grade 8 hardware for installation.
NOTE: ALL CONTROL ARMS ARE DESIGNED TO USE PROFORGED BALL JOINTS. .
Learn MoreThe Porterbuilt Stage 2 Basic Front Kit for '63-'87 Chevy Trucks improves ride quality and overall driveability by replacing the factory lower control arms and and factory coil spring with an air spring.
Learn MoreThe Porterbuilt Bolt-on Body Drop for the 1967-1972 C10 is for those guys who just can’t be low enough! It is designed to make it easier to set the pinch weld level to the bottom of the frame.
Learn MoreWilwood Forged Narrow Superlite 6R Front Brake Kit
12" 1 Piece Rotor and Hats, SRP Drilled & Slotted Available
6 Piston Calipers, Red or Black Available
15" Minimum Wheel Diameter
* FOR USE WITH WILWOOD C10 STEEL SPINDLES
Learn MoreWilwood Forged Narrow Superlite 6R Front Brake Kit
6 Lug
12" 1 Piece Rotor and Hats, SRP Drilled & Slotted Available
6 Piston Calipers, Red or Black Available
15" Minimum Wheel Diameter
* FOR USE WITH WILWOOD C10 STEEL SPINDLES
Learn MoreThe new Porterbuilt sway bar is manufactured in-house and is available for early Dropmember equipped trucks. It comes raw and includes all mounting hardware.
Learn MoreThe new Porterbuilt sway bar is manufactured in-house and is available for trucks equipped with PB Fab control arms and the factory crossmember. It comes raw and includes all mounting hardware.
Learn MoreThe Porterbuilt cowl mounted hood hinges are the perfect solution to relocating the hood hinges once the factory inner fender wells have been removed. They are available for model years 1960-1972.
PRODUCTION TIME ON HOOD HINGES IS TYPICALLY 2-4 WEEKS Learn More